58714112402 Kenmore Dishwasher - Instructions

Pulled off the old gasket and replaced it the same way with the new one.

Simply pulled old gasket out with hand, and slid the new one in place!

I simply had to take the replacement rack out of the box and put it in the dishwasher. I was sent exactly the right part, as ordered, and had no difficulties at all.

Used pliers to pull out the old gasket. New gasket snapped into place. Notice where notches in the gasket are when the old one is removed, so the new one can be properly oriented. It was not necessary to remove the door.

I measured the length of the gasket, using the old one to measure the length. Cut it to that length and installed it. VERY SIMPLE TO DO! But it didn't stop my leak--turns out there was a small leak in the bottom of the tub that was easily fixed with some silicone. The dishwasher's like new now!

I followed directions from a video on this site and written directions in order to make the repairs. Pulled out the old gasket from one end with pliers . I cleaned out the slot in the door of any food or dirt and replaced with the new gasket. It was a very easy and quick repair that allowed me to use my dishwasher quickly. Thanks for the help.

1-2-3. Finished ! I had watched your video on how to !

We looked at the diagrams for our Model number on Parts Select to find what was missing. We ordered the parts they arrived in two days. It took me 5 minutes to install the new parts. I left the dishwasher out from its locatation so that I could run a cycle and watch for leaks as it ran. After a full cycle, there were no leaks and I put the dishwasher back. Piece of Cake (or a lot of luck)!

Replacement was simple.

Watching a YouTube video that was attached to an email, I was able to install my new dishwasher filter in no time without any tools. Thank you.

Removed front cover. No instructions so I removed all the screws. Only the bottom 2 need to be removed(1 on each side) then push cover up to unlatch. Remove 2 wires and 6 screws. Replace soap dish unit. reinstall screws and wires. Replace front cover. The hardest part is the front cover.

Had trouble installing the new gasket at first. Fell inside the door, and would not stay in the groove intended for it. After watching the video on your website, learned is best to angle the gasket and work in slowly to the groove from one side. Much easier then

Removed front panel of door, to get to the screws that hold the door on the hinges. Removed door, pulled gasket with pliers from bottom of door, not easy to get out because of mineral deposits. Had to push quite hard to get new gasket in. Put every thing back together and no leaks. I live in Alaska and I tried to order the part through Sears and they wanted $18.95 for shipping for a $12.87 part. The part with PartSelect was $14.92 but only $6.95 for shipping. I ordered the part on a Tuesday and recevied it on that Friday. We in Alaska get very tired of companies thinking we live on another planet. Thank you PartSelect.

Removed the screws at the top which held it in , then I pulled it outside of it's shell, took it apart and took the drain part off, replaced with new drain part, put it back together the same way I took it off, pushed it back in, put the screws back in, tested it, and it worked. Ta Daaa!

I thought these were OE racks they are not. They did do the job. However, I like OE parts the difference is exactly where the fold over rack on top rack goes the tines were not there to clip on it into there was a larger gap. So it was almost the same except the most important area. Same for the cone that clips in the center of the top rack. It is not as tight a fit front to back as it should be so it moves around more. I was concerned that the jet of water from top would miss the cone but it seems to be ok. So far so good. The racks did the job dishwasher is still cleaning dishes. But aftermarket parts are almost the same just not quite the same.