58714008002 Kenmore Dishwasher - Instructions

Pulled off the old gasket and replaced it the same way with the new one.

First of all, I got the part 24 hours after I ordered it. That in it self was a feat. Second, I followed everyone elses instructions, pulled the old gasket out with a pair of needle nose pliers, cleaned the area as good as I could, found the notch for the slot on the gasket to slide into and viola...it slid in and stayed in. No more leakage whatsoever! Thanks for all of the tips!

This was a dishwasher that my employer threw out due to the excessive time it was going to take getting the broken part - all of the appliance stores I contacted had them backordered. Since I'm a DIY and Internet savvy person, I decided to go to the Internet page and use the IPB to determine the correct part, and ordered it. I installed the dishwasher, and waited...
10 days after ordering the part, it came right to my door. Installation was very simple; remove 7 Phillips screws from the front panel to access the latch mechanism, remove the two Torx screws holding the latch assembly, disconnect the wires from the latch assembly, and do the reverse procedure to re-install. No latch alignment was necessary, just screw the assembly right back in place. (Yes, I made sure the power had been disconnected!) The door gasket did not need to be replaced at this time.
A very quick and simple procedure for the DIY-type person that can handle simple tools.

Turn off power. Took out screws holding control cover on, (left loose and hanging in the front of the door by the connector wires).Disconnected the two wires at the bottom of the switch. Removed two torx screws, pulled switch out. Reversed procedure to install new switch (which isan exact replacement). turned power back on, tested door latch, washer works perfectly again.

New piece snapped right on

1. Engage B.R.A.I.N. :
B: Break open the Box. You know you'll never get it back in
R: Read Instructions: It's not more packing material.
A: Assemble New One: Put it together just like the old one
I: Ignore Instruction: Seriously, sharp edges will cut me?
N Never listen to the wife Or at least pretend to be listening

Removed two screws,one on each side of the bottom part of the door. The door cover then comes off. Then 6 screws hold on the dispenser. Shut off power and remove two wire connections. Replace dispenser. Replace lower door cover and two screws. Done.

Unhooked the dishwasher and took it out. Laid the dishwasher on it's back. Located the drain pump and took it off. Put the new one in it's place. Hooked the dishwasher back up and tried it out. Everything sounded and ran good. Easy assembly. Took 30-40 minutes if that.

The old gasket was worn. I pulled out the old one, put in the new gasket. I trimmed the ends to fit and that was it.

Took out the two retaining screws and pulled the unit forward. Took the old door strike out and put in the new one. This site is where I go for all my appliance repair parts!!!

Used pliers to pull out the old gasket. New gasket snapped into place. Notice where notches in the gasket are when the old one is removed, so the new one can be properly oriented. It was not necessary to remove the door.

Watching a YouTube video that was attached to an email, I was able to install my new dishwasher filter in no time without any tools. Thank you.

I measured the length of the gasket, using the old one to measure the length. Cut it to that length and installed it. VERY SIMPLE TO DO! But it didn't stop my leak--turns out there was a small leak in the bottom of the tub that was easily fixed with some silicone. The dishwasher's like new now!

I snapped the new one into place and ran the cycle. This time, everything came out clean, except for the bowl that had caked on cinnamon from the weeks I didn't have the part

Simply pulled old gasket out with hand, and slid the new one in place!