56121TAWW General Electric Washer - Instructions

I first removed the screws from the top of the washer electric panel. Then pulled it forward. I then removed the plastic clip from behind the knob. Then I removed the screw holding the timer in place. And then removed the one single wire and the connecting plug. I then plug both wire assemblies in to the new one, slid both ears under the brackets and inserted the one screw. Then just put the screws back in the top. It works great!!!!!

Drain tub. remove 2 hose clamps and hoses. R&R 2 screws that hold pump.

It was very easy, just one screw to get the belt on, then it was just putting in place and putting it back together took the longest.

It was almost a complete tear down. Most difficult part was discivering how to remove the front panel. Slip a putty knife between the top and front covers. push and depress the spring tab on each side. The left hand nut on the hub was difficult. I had to get a neighbor to hold a large pair of pliers while I put a pipe wrench on the nut and hit it with a 2 lb. hammer in order to break it loose. Puting it back together do not forget to reconnect the level sensing hose to the level selector, I did. Machine will not perform without it. You can do it! I did.

Took front panel off the washer and found the pump working but no water drained from the tub. Took the motor off the washer by removing the two 10mm screws and attaching hoses. Decided to take the motor apart and found the propeller shaft has broken off inside the pump. Ordered new motor from Partselect and replaced it. Washer is working fine now.

First off, the repair part arrived in only two days. The schematic was very detailed and accurate on your web site. Once the part arrived and removed from the bag, it was a snap to install with just a needle nosed pliers. Total time was less than 5 minutes. This was the first time I had used PartSelect and you can bet I'll be back. Thanks again. Gary K. in IN.

Remove four screws which held the front cover of the washer. Dropped the cover down to expose the temp. switch. Turned the switch 1/8 turn counterclockwise which removed the switch from the cover. Pulled of the four pigtail wire leads and then installed the new switch in reverse order. Very easy!!

Just used hands to pry open the old agitator from the washer. If one angle does not work try another and go in a clockwise direction. The new agitator had a new coupling at the bottom, so I needed something to push it out from the top, found a long metal rod and easily pushed it down and out. Verified that new coupling was exactly the same as the old one. The old one was good so I just pushed the new agitator down on the old coupling and it worked fine.

We pulled up diagrams online and read a lot about the repairs. Four screws on top took off the electrical panel. Two clips hidden under the front of the top panel released the front panel. We followed the clear tube up to the water level pressure switch. We disconnected the previous switch, and connected the new one, one wire at a time. We tested and found that the water now stopped filling. Put the washer back together - done! Cost - $30 and 1/2 a hour total vs. calling a repair person.

Removed the front panel with a stiff putty knife, removed the worn belt. Placed the new belt on the front pully and than the rear pully, turning clockwise. After checking the spin cycle I put the front panel back on and I was done.

Should be noted that the basket must be rotated on installation to find the best balance point!

First I pulled off the front panel using a flat blade screwdriver to get it started. Then I could watch what happening as I tried starting the washer. When I put the dial to the Rinse Cycle and pulled the dial to start the washer, it would start to run for about 5 seconds and then stop. I tried this several times and the same thing happened. I noticed the water pump located in the front lower right hand corner was not running. It would only hum. I drained the tub by holding the wash machine drain hose into a bucket. If I held the hose down toward the floor, the water would flow freely out of the hose and into my bucket. As the bucket filled up I just raised the hose, emptied the bucket and repeated the process until the tub was empty. Sure saved time over trying to empty the tub by bailing the water out with a can. After the tub was drained I removed the two hoses from the pump and then the two mounting bolts and the pump was out. I bench checked the pump with an electric cord and it stilled just hummed. I knew for sure then the pump was bad.

I then ordered a new pump from PartsSelect.com. I entered my wash machine model number and PartsSelect gave me a picture of the replacement pump. I was a little worried that it did not look the same as my old pump but I ordered it any how. The night I got the pump I installed it in about 30 minutes. No problems, it just worked like a charm. Thank you PartsSelect.com I will definitely use you for all my appliance repairs in the future. I know there will be more.

I pulled agitator off revealing rotted hub. Had to remove inner basin from machine. This required pulling off top and tying up to be out off way . I had to get the control panel out of way. Removed back screws and moved it up as though hinged. I had to remove the water fill piece, as this was impeding removal of basin. I had to remove top ring off of inner drum. Needed a second person to hold control panel away as I removed drum. Once drum was out, it was an easy task to replace the rotted hub. I then needed to get the portion that was rotted and still on drive out. Could not wrench the hub nut out due to lack of leverage. Split nut with a chisel. Once old nut out, I cleaned up threads, put inner basin back in, again utilizing assistance in holding control panel out of way. Reinstalled in order. Before I had gone too far, I found that a six pronged jumper had fallen off of the controls. Found where it had been and re-installed. Put remainder back in reverse order. Machine back on line, and working properly.

Open back cover and found that drain pump had a bad seal. Took it apart and bought new seal some what same size. Put everything togather and start washing clothers and wife complained that it became wost the before. When on line and found pump and price was just right to take a risk. Ordered on sunday and got ups tuesday.
Replaced pump on Sunday and leak was gone and wife was happy.

------Got chicken and beer that Sunday--------------

I removed four hex screws from the top of the washer. I found the water level pressure switch and removed the dial. I turned it to remove it from the holding bracket. I removed both wires one at a time and placed them in the new switch one at a time so I wouldn't get them mixed up. I put the new switch in place and put the top back on using the hex screws. The dial was replaced. When I tested the dial I found that the dial did not match up to the water settings. They didn't even come close. Although the numbers were close on the switches, they were different. I had to remove the new switch and put the old one back on until I can locate the correct switch for my washer.