4RF302BXDW0 Whirlpool Range - Instructions

Turn off the oven circuit breaker. Remove 2 screws that hold the element in place. Carefully pull element out, about 3 inches and remove 2 attached wires by holding the element and pulling the wire clips off of the old element. Slide wire clips onto the new element and put the screws back in.

Removed all surface burners from range, removed range top screws, and suspended range top. Removed plug-in block mounting screw. Cut wires for plug-in block close to original wire-nut junction. Inserted contacts & wires from kit into plug-in block. Slid a provided shrink sleeve onto each wire. Stripped wires on range wires and then connected them to the plug-in block wires with the provided high-heat wire nuts. Selected one of the two provided plug-in block brackets that matched the original bracket on the range. Used a butane lighter to shrink the shrink sleeves over the wire nut connections. Snapped the appropriate bracket onto the plug-in block. Reassembled everything in reverse order and plugged in new element. Note: my only two issues are that the two high-heat wire nuts provided in the kit were a bit too small for the wire gauge in my Whirlpool range. It took some fiddling on my part by carefully re-stripping the range wires to get the wire nuts twisted on securely. Two more wire nuts of the next size up would have been appreciated. Also, I found that the provided plug-in block mounting screw did not find fit my range. No problem; I simply re-used the original screw. All in all, an easy repair and the element works perfectly.

Ordering the part online was easy. It arrived in a timely manner. I found a terrific video online showing how to install the terminal. It was so easy. Thank you for the great instructional video.

I took out the coils manually by pulling them out with slight pressure. Then I lift the hood by first unscrewing the four screws. I have never done anything like this before just intuitive sense to locate the screws that needed to be loosened. Afterwards I remember placing something underneath like a piece of 2x4 wood block to act as support to hold the hood open so I can work on the coils. The parts I got are exactly the same as those I am replacing so I just copied the connection and voila my electric range is working like new. Well of course before I touched anything, I made sure I turned off the main switch and that nobody switches it back on without my knowledge. Thanks for providing the parts, I just saved myself from buying a $600 electric range.

remove burned out eye, replaced with new eye.new eye does not fit exactally correct onto splash pan as point on end of steel " rod " not pointed enough to slip into mate on splash pan

Disconnect power to the oven at circuit breaker. Most important confired power removed by turning on buner,also with electrial meter. Remove hex screw. Pulled purner forward approx 3 inches remove the two wires to burner element . Installed new burner reverse rotation . Returned power to oven,all was well no problems. Not to sure of burner wattage on old and new unit,as two burners are avaiable for this unit. All ok . Thanks to parts select for speedy part needed

ordered new broiler pan

Someone did the repair for me.

Pulled out the old burners and put in the new ones.

Shut off power to the stove.
I removed the screw that held the block in place. Then I lifted the top of the rage to get to the wires. I cut the wires from the old block and stripped back the insulation. Next I put the heat shrinking sleeve on. I attached the new block with the wire nuts, pulled the sleeve down and used a hair dryer to shrink them. Then you just hook it back on screw it in and your done.

I took the old wires and plug off and replaced it with the new block it works fine

I removed the block, cut and spliced the wires to the new block and installed the burner. I used the new style block kit and saved about $30. It worked great!

Repair was very east. The suppliers package had all of the necessary parts ceramic wire nuts wire Ect. Excellent.
Will buy from Part Select Appliance again.

turn off electric breaker, unscrew the 2 screws unplug the 2 ends replace old element with new repeat previous steps but unfortunately the control panel was also failing and that item has been discontinued.

Removed the small metal panel covering the main power terminal in back of the electric range. Removed the nuts holding the red, white and black electrical wires from the range using the appropriate socket (there will be two nuts on each bolt end). Removed the two screws holding the main power terminal block with appropriate screw driver. Connect the new main power terminal block to the range using the two screws. Reconnect the red, black and white electrical wires coming from the range using one nut for each wire. IMPORTANT: do no over tighten the nuts because the bolts could snap. Reconnect the pigtail and secure the small metal panel covering the main power panel.