4KPDI620T2 KitchenAid Dishwasher - Instructions

Found the adapter on Parts select through a google search. Unscrewed the existing faucet aerator and srewed in the adapter. The plastic shrink wrap holds the washer and screen in place, so don't open it until you're ready to install. Finger snug does it, only use the pliers to remover the old aerator from the faucet. Normally, I don't use pliers, but both of these parts were round and had vertical serrations to engare the plier teeth.

Sorry to say that all I did was screw the cap on in about 3 seconds. Not a repair.

I had called an appliance repairman...I gave him the model #- he called me back in 2 seconds and said it was too old.. no parts available.. wanted to charge me $100 to come and look.I found parts select online. the part came in one day... and my handy man/put the new bracket on.. the dishwasher was put in new in 1991 and still works like a charm..thanks thanks

Replaced the faucet adapter, works fine

Just followed directions included.Am extremely pleased with the appearance of the new panels they matched my new appliances.Also I did not pay for express freight but received my order in only two days.Very pleased with Part Select.Thanks Al S

used screwdriver to remove roller axle. Snapped on new axle and wheel. I ordered two extra sets just in case future wheels brake. simple. 16 Year old dishwasher works fine!!

Very easy. Disconnect power to the dishwasher via a breaker or fuse. Open the door and remove just the 4 screws on the inside lip of the door. Do not remove the screws hoding the closing brackets. Remove the front glass and chrome panel between the control panel and the kick panel. This will give you access to the soap cup and bi-metal. Remove the one retaining screw and remove the bi-metal,taking note of the position of the wires. Remove the wires, by grasping the connectors (I used needle nose pliers for this), not the wires, and re-intsall them on the new bi-metal. Re-install bi-metal on soap cup assembly, "cock" the release lever by closing the soap cup cover and manually trip the bi-metal to make sure it will release the lever and open the cover. Re-install the front panel with screws. Restore power and test appliance.

Easily one of the easiest repairs I have ever done. The new bits snapped into place and now the bottom rack rolls in and out like brand new.The ease and speed of finding the parts was really helpful. This is an old model and to be able to find the exact parts I needed so fast and so cheap was great. Oh and they arrived the day after I ordered them! Insanely fast!

Pried off broken axles, replaced with new ones & snapped on new rollers.

I took off all the old axils and put new ones on,and then I slide the wheels on and That was all is to it. EASY!!

I bought the portable dishwasher on Craigslist, and it didn't have the connector that goes on the kitchen faucet. Ordered it here, got it in a few days, and didn't need any tools - just had to screw it on. Good as gold!

I popped all the new parts in place and all is well.

The previous pump needed to be removed, install new. New pump mounting bracket hit existing mounting bracket from an adjacent part. 1. Wire contacts removed 2. Copper incoming line was disconnected from brass elbow. 3. Hose to pump removed using pliers for wire clamp, and flat head screw driver to prod hose off. The used pump is now in one's hand. The new pump would not fit using existing screw holes. The mounting bracket was moved to the left, using the one pre-existing hole and right hole in mounting bracket. The left hole of the mounting bracket was used as location for another hole to be bored/drilled out. Two drill bits of different sizes were used, along with the same sheet metal screw which was in previous mounting bracket assembly. Pump design has been changed from two wire coils to one wire coil. 1. The hose was re-connected using pliers. 2. Copper compression fitting lined up with brass elbow again. 3. Two Wire contacts were attached; previously there were Three contacts. 4. Second screw was added in newly bored hole. Plenty of room moving to the left. There is one loose wire contact.

broke off the remaining roller axles, pushed the new roller axles into place, then snapped the little wheels onto new axles. I FELT LIKE WONDER-WOMAN, FIXING MY OWN DISHWASHER!!!

unscrewed 4 screws on top panel and 2 on bottom panel... real easy fix.