Models > 4KB25G1XGA5 > Instructions

4KB25G1XGA5 KitchenAid Mixer - Instructions

All Instructions for the 4KB25G1XGA5
61 - 75 of 156
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
gears and bearing failure
inspected and replaced worn components
Parts Used:
Mixer Rear Bearing Mixer Front Bearing Gearcase Housing with Gasket Mixer Transmission Gasket Mixer Worm Gear Worm Following Gear Mixer Thrust Bearing Kit
  • Gary from Hamburg, MN
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
4 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Last repairperson broke the top cover of the gearcase ; still need this part .
Easy ; remove belt ( 1 screw ) remove cover , and there is the complete drive . I still need the top plastic cover which is cracked and broken where the bolts go through . Please quote this part .Conradt
Parts Used:
Gearcase Housing with Gasket Mixer Transmission Gasket Worm Following Gear
  • conradt from el paso, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The mixer started making a loud knocking noise
Unscrew the top and remove it , 4 more screws to remove the top of gear box , wipe out the old grease , lift the gears , but to remove the center gear you need a special narrow tip plier to remove the snap ring . Changed the center gear , apply new food grade grease and with reverse order putting back all remaining parts . Worked fine .
Parts Used:
Hub Gear
  • Reza from STAMFORD, CT
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
white plastic part on the lifter handle
Took off all the screws to open the mixer and install the new parts.
Parts Used:
Bowl Arm Lift
  • ROBERT from LARGO, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
gear teeth worn off worm gear
replace worm gear
Parts Used:
Worm Following Gear
  • Jamie from Jamestown, ND
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
3 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Worm gear stripped.
Remove covers, open gear box, remove lock ring and gears to deterime which gears were bad. Remove old grease, install new gears and pack with new grease.
Parts Used:
Mixer Worm Gear Worm Following Gear
  • Jerry from Southport, NC
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Part broken
Easy thanks to your instructions
Parts Used:
Bowl Arm Lift
  • William from North Olmsted, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Gear Stripped was trying to replace
Could not get it properly installed. Had to take to a repair center for completion.
Parts Used:
Worm Following Gear
  • Stuart from Pittsford, NY
  • Difficulty Level:
    Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Speed control panel was replaced
Just followed the video.amazing!!got my kitchen aid back.
Parts Used:
Stand Mixer Speed Control Board and Knob (Black)
  • Madeleine from NEW YORK, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken gears
Fast
Parts Used:
Hub Gear
  • walter from SOUTH ELGIN, IL
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
motor would surge after a few moments of running then die.
so easy to remove the switch. I first marked the wires, 1-2-3-4 and then removed them from the old switch. removed the old switch and replaced with the new one and plugged in the wires as per markings. tried it out before replacing the top and it works perfectly. no longer timid about effecting repairs on my own. the diagrams on the website were a great help. this is a great company to do business with. part was here in 3 days.
Parts Used:
Stand Mixer Speed Control Board and Knob (Black)
  • Fred from Coeur d'alene, ID
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Speed control switch went out
Unplugged wires from old switch, plugged them into the new switch. The new Switch have the mounting brackets in different places from the old one. Be sure to match up the numbers by the posts with the correct wires
Parts Used:
Stand Mixer Speed Control Board and Knob (Black)
  • Joyce from STRAWBERRY PT, IA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Motor knob
Watched utube
video how to repair and ordered part, easy
Parts Used:
Stand Mixer Speed Control Board and Knob (Black)
  • Susan from KIRBYVILLE, TX
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Gear housing cracked, gear had nic in it
Removed old housing, pulled spring clip, slide on new gear and replaced clip. Put on new gasket and housing. Replaced outer cover. Done.
Parts Used:
Hub Gear Gearcase Housing with Gasket
  • Bob from ELIZABETHTOWN, KY
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken gear case.
Remove and replace gear case. Apply food grade grease secure with screws.
Parts Used:
Gearcase Housing with Gasket
  • David from CEDAR CREEK, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 4KB25G1XGA5
61 - 75 of 156
Back to Top