4KB25G1XER3 KitchenAid Mixer - Instructions

Removed plastic cover, removed grease and put in new mixer and put new cover back on.

I did not do the repair myself, however, I contacted a suggested service company which in turn was a company I had used before when I had problems with my JenAir microwave. Excellent service, prompt and very professional. Thank you JenAir for your assistance in providing promptly the parts needed to complete this job.

Took screw off band. This revealed 4 screws to upper housing. Removed 4 screws and lifted upper housing off . To my surprise I found no screws holding gear housing cover in place. You could tell they were there at one time. Should be 4. I removed cover disasembled what was left of gears. Cleaned old grease ordered parts. Thought since there was only 1 screw on diagram it would ship 4. No big deal. After recieving parts further inspection revealed no screws holding motor in place. This blows me away. Anyway off to local hardware store for more screws. Got home slapped it togethere in 10 minutes. Ordered this off TV about 6 years ago. They must have had it in for repair and forgot to put it back together. All that aside it runs better than ever. Thanks much Michael

disassembled unit gear head and replaced broken part, then reassembled

Watched the video. Ordered the parts. Watched the video again. Replaced the worm follower gear and bearings on the worm gear. Added grease. Installed new gear housing. Put it all back together and tested. Works like new. Now I get cakes and goodies again and have a happy wife who thinks I'm super handyman. Thanks

watched the youtube video on how to repair a Kitchenaid Pro 600.

After removing the single philips screw from the back of the unit, the metal band will come off. Under the band you will find 4 phillips screws. Remove them to get the cover off of the unit. Once open, access the gear box in front by removing the four philips screws holding the gear box cover down. Remove any old grease from the unit as there may be pieces of broken gear in the grease that will damage the new gears. I used a small plastic scraper, some paper towel, rubber gloves and q-tips to get all of the grease out. Try to make a note of how much grease you removed and from where, so that you can replace about that amount later and in the correct spots. To remove the bevel gear remove the split ring holding the bevel gear down on the vertical drive shaft. Once the ring is removed it will be easier to move the bevel gear, but I found that it was somewhat press fitted on the shaft and I needed to use some channel locks to gently rock it back and forth to get it moving up the shaft. I then, also, (since I was in there) replaced the worm gear underneath the bevel gear by tapping the retaining pin out of the hole above the worm gear and then tapping down on the vertical drive shaft with a hammer to push the planetary gear down and out of the unit. Once free, I then regreased the planetary and reinserted it in the holder taking care to align the gears on the shaft and the panetary housing. Then I tapped the worm gear all the way down to the base taking care to keep the recessed notch on the top of the worm gear parallel to the pin hole above it. Then I replace then pin and tapped the bevel gear down onto the top of the worm gear and replaced the split ring. Realigned all of the horizontal and vertical gears and then repacked the grease. Closed up the gear box and test ran the unit on low. THen closed up the rest of the unit in reverse of opening.

Noticed worm gear was worn out, ordered the parts, it came very next day. On YouTube instructions were very easy to follow. Important point to remember,I washed the parts in water with chlorine in it. Retaking ring was tough to take out, as I did not have parrot beak plier, could not find it at Home Depot or Lows. Putting the retaining ring I used circular nut driver, to press it on the shaft to slide down by hammering it. While assembling follow the instruction step by step from the you tube. Machine works smoothly. Performing well. Thanks to part select, excellent web page, efficient delivery. I would recommend them to all.

You must have new bevel gear and can of food grade grease, ordered together. 1. Remove screw from back of mixer, holding the trim band; remove band. 2. Remove four screws holding the top cover. 3. Remover cover 4. Remove two screws holding the pc board and motor speed control; lift board out of the way. 5. Remove four screws holding gear cover; remove cover. 6. Remove as much gear grease as is accessible; discard. 7. Remove snap ring from vertical shaft holding bevel gear. 8. Remove horizontal shaft/gear by lifting straight up. 9. Remove bevel gear by sliding up shaft. 10. Remove cross pin holding lower gear. 11. Remove lower gear by sliding up shaft. 12. Remove vertical shaft and rotating head by tapping on top of shaft. 13. Clean all grease from gear case and on all gears (ground metal from bevel gear will be in this grease). 14. Clean all grease from inside gear cover. 15. Making certain gear case is now clean of all old grease, use putty knife to place grease in bottom of gear case. 16. Rub light coat of grease on vertical shaft and slide shaft back up into bottom housing. 17. Slide lower bearing back down vertical shaft. 18. Reinstall cross pin holding lower gear. 19. Place grease on lower gear. 20. Slide bevel gear down vertical shaft, making certain recess in underside of bevel gear lines up and sits completely over top of lower gear; when the bevel gear is fuly seated the snap ring groove will just be showing on the vertical shaft. 21. Reinstall snap ring. 22. Lightly grease shaft of both ends og horizontal shaft/gear; make certain ball bearing on front of shaft is also greased. 23. Slide ball bearing, spacer and bronze bushing on front of horizontal shaft. 24. Silde bronze bushing on opposite end of horizontal shaft (flange on bronze bushing is placed facing the gear). 25. Place assembled horizontal shaft/gear into lower gear housing. 26. Liberally grease all gears, 27. Replace gear cover, replace screws. 28. Replace pc board and motor speed control. 29. Plug mixer in and run on lowest speed for at least 10 minutes;increase speed until satisfied gears ar running smoothly. 30. Replace top cover and trim band. Bake something

The repair is actually quite simple. The Snap Ring Pliers are essential. Make sure you clean out all the old grease in the machine and replace with new grease. The metal dust will act like sandpaper and destroy your new gear. There are several videos on YouTube which go through the process of repair and part replacement, I found these quite helpful. Good luck! DIY!!!!

Removed top cover, remove snap-ring on shaft, slide top gear and worm gear off. Clean all the grease out and clean parts. Installed new worm gear and parts. Repacked with new grease, careful not to much, leaving room for expansion.

removed the cover, separated the gear casing, cleaned the gears, replaced the thrust bearing kit and worm gear, greased all and reassembled. Wish I would have known to order the grease, it would have saved a couple bucks in shipping.

Worm gear strips usually after the lower gear housing breaks. Tore down cleaned grease and shrapnel out, replace stripped worm gear and lower housing. It's convenient that the lower housing plate comes assembled with new bushing and gear. This is now the third one of these expensive mixers I have repaired, word got out that I fix them, and this is a very common problem. Repairs have been for friends and Church, so I don't charge any labor, it's kind of fun, messy, but fun. Note to Kitchen Aid: Please strengthen lower gear case.

After trying to make a batch of heavy frosting, my KitchenAid mixer final stopped turning. After watching a video of how to change the grease in a similar model on PartsSelect and seeing it wasn't that hard to take apart, I decided to give it a try myself. Removing the cover exposed a completely worn gear drive. Luckily, it was easy to determine which parts needed replacing and PartSelect sent them in no time. Once I put everything back together, it sounded terrible which was pretty tough to take. As it turned out, the problem was flecks of metal from the gear were still in the grease and were getting caught in the mechanism. Once I thoroughly cleaned all the grease out and gave it some fresh grease the machine worked great. Much better than before. I only wish I had swapped the grease out at the same time. Thank you PartsSelect for saving me hundreds of dollars on a new machine!

Used the meat grinder attachment, with the retaining ring too tight for the motor to turn the augur, so a gear stripped and the mixer would not run. I opened the mixer top, removed the transmission cover, removed enough grease to diagnose the problem (6 teeth stripped off the steel worm gear). I ordered a replacement steel worm gear and, while I was at it, a new retaining ring, bevel gear, retaining pin and the large planetary gear, as I could not tell the condition of these until I disassembled the whole gear train. I then removed the gear train components (needed a snap ring pliers to remove the retaining ring -- I don't recommend trying to remove it with an y other tool), washed them in acetone, cleaned out the transmission case and went over it with a magnet to get stray gear tooth remnants, replaced the worm and bevel gears and reassembled, using the original planetary gear, retaining pin and retaining ring. Filled the bottom of the transmission with planetary grease first, then, once the gear train had been replaced, slathered a big pile of grease over it, replaced the transmission cover. The machine then ran perfectly, so I replaced the mixer's top cover and decorative band and was back in business mixing with it about 30 minutes after cleaning the last of the grease off my hands. I should mention, I used a LOT of paper towels for this job. This was a fun job and I was sorry that it was so easy to do, as I enjoy working with gears and grease.