All Installation Instructions for KitchenAid Mixer 4K5SS

Damaged insulation on the cord

Removed back cover, disconnected the 2 push-on connectors, removed ground wire screw. Reversed the process to install new cord.

Parts Used:

Power Cord

Dennis from WESTERVILLE, OH
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

The mixer broke the worm gear(the only plastic gear inside the mixer) and needed replaced.

I took apart the mixer housing and removed all the screws. The most difficult part was the two pins that needed to be removed with a metal punch. They were in fairly tight. The mixer came apart pretty easily and it was obvious which part needed to be replaced as it was broken and missing teeth. After replacing the gear and applying new grease for smooth operation, I simply put it back together and it has worked like new ever since.

Parts Used:

Worm Gear

Dustin from JACKSONVILLE, NC
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

spring latch was broken

changed the part

Parts Used:

Mixer Bowl Latch Spring

Jack from GLEN ALLEN, VA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Beater replacement

No repair needed

Parts Used:

Flat Beater

William from SPARTANBURG, SC
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Mixer went to high speed immediately on starting

Simple fix actually. UNPLUG mixer and remove the one screw on top that holds on the back. The Phase control board sits under and behind the paper insulator and "switch" assy. Remove the 4 wires with a pair of needle nose pliers, the one screw holding it to the back of the mixer and install the new one in reverse order.

Parts Used:

Mixer Phase Control Board

Michael from JACKSONVILLE, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Mixer operarates at high speed only.

Removed old one and replaced with new one.

Parts Used:

Mixer Phase Control Board

GALO from DECATUR, GA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

broken spring latch

Unscrew the broken latch; remove it; screw in the new latch. Very, very, very easy to do.

Parts Used:

Mixer Bowl Latch Spring

Mariette from VALPARAISO, NE
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Spring latch snapped off making bowl unstable and unless hand stabilized wobbled too much to use.

SO SIMPLE!!!!! Using a regular screwdriver, remove the remains of the Spring Latch. Place new one over holes and screw new one in place using the currently used screws. May wash off screws first if caked with gunk. OMG!!! TOOOO easy and saved me from throwing out a very terrific 40 year old PRO LINE KITCHEN AID MIXER!! To replace it would have been hundreds of dollars.

Parts Used:

Mixer Bowl Latch Spring

Marcia from NEW YORK, NY
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Control stuck in high gear.

With the mixer being over 30 years old we believed it has going to have to be replaced. However, my husband jumped on uTube and looked at reviews for the problem. Motor was only running on high speed. Reviews said to replace the phase control board. Repair was very quick by just taking off the cover. Removing the old board and connecting the new. Mixer is working awesome once again. In such a disposable society it is great to be able to fix vs trash. Happy Baker.

Parts Used:

Mixer Phase Control Board

Ann from OSSINEKE, MI
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

bowl shaking during use

line up the screw holes and screw it

Parts Used:

Mixer Bowl Latch Spring

Ely from Monsey, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Burnt brushes

The brushes are located on each side of the tilt head of the mixer. I used a screwdriver to remove the screws, removed the brushes & replaced with the new ones. Runs great again!!

Parts Used:

Mixer Motor Brush

Sabrina from BUNKIE, LA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

One speed only and surging

I replaced the phase control board because the mixer had only
one speed and was surging. I noticed from other posts that it
is important to note the setting of the speed plate before you
remove it in order to remove the phase control board. Also be
careful removing the associated 'slip-on' terminals as it would
be easy to damage the speed plate. If I ever do this again I
will go ahead and replace the speed plate, probably the cheapest
item to replace. The operation was a success and the mixer is
back in business. Thanks.

Parts Used:

Mixer Phase Control Board

Joan from HALEYVILLE, AL
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

My stand mixer stopped mixing!

I watched a YouTube video all the way through, then watched each segment and followed along with the video. It was messier than the professional repair guy, but it worked out fine. This is not a difficult repair when you can watch a video and follow along. It saved me about $130.

Parts Used:

Mixer Worm Gear & Bracket

Carl from HAMPTON, NH
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Decorative plug at top of mixer fell into the bowl and jammed the mixer stripping gears

Watch U Tube video. Take care to keep track of disassembly. Hard part was to have 4 types of screw drivers to fit the different screw heads. Be sure to clean broken gear clogs out of the grease. Parts select lady was a great help. Download Parts select diagram for extra help. Time and patience!

Parts Used:

Worm Gear