All Installation Instructions for Hoover Range 4855

not a prblem,just necessary to replace

even though these sre washable filters it's still necessary to change them after so much time

Parts Used:

Grease Filter

Peter from Wilson, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Broken knob dhaft

Replaced wires from broken to new part.

Parts Used:

Surface Unit Infinite Switch Kit

Richard from THE WOODLANDS, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Could Not Use One Burner

Turned power to stove off. Removed two screws from cover - lifted cover up and pulled switch out and disconnected wires. Put new switch in and connected wires. Made sure that it was in correct position by placing knob on to make sure off position was correct - then placed plate in position and closed - put two screws back on plate and put new knob on. Turned power back on and turned knob and burner back in operation

Parts Used:

Surface Burner Knob

Surface Unit Infinite Switch Kit

Anne from Bedford Hills,, NY
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Elec. stove-top knobs (imprinted with HI to LO numbers 1 to 10)worn to non-readable.

Knobs sent fit the shafts, but due to molded internal stop wouldn't seat. Had to drill out the stop, and also file down the shafts a bit for knobs to seat acceptably closer to stove-top.

Parts Used:

Surface Burner Knob

Lenice from Stuart, FL
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

super old Jenn-Air range needed an element

Pulled out the old one-couldn't find it ANYWHERE that was a comparable match except for partselect. shut off breaker to oven-put in the new one-hard to reach in due to limited space and hard to see due to sticking your head in an oven.used a mirror/flashlight to see behind element to unscrew and screw it back in.Other than space restriction and light-pretty easy. Works great! Thanks for HAVING the part!! :)

Parts Used:

Bake Element with Screws

Edgar from Montgomery, IL
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Element quit working

Ordered the part. It arrived in about 4 days. Took a screw driver and in just a few minutes, it was working again. BINGO

Parts Used:

Bake Element with Screws

Alyce from San Antonio, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

electric bake element had a physicle break

First I removed the two screws that hold the element in place. Then I pulled the element out about 2 inches & disconnected the two wires, Then I removed the ground wire. I then wired in the new element ( this was the only tough part of the process, because I had a very tight space to work in- less than 2 inches.

Parts Used:

Bake Element with Screws

Edward from Summit, NJ
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Existing knobs were bent & unreadable

Removed old knobs and installed new. No tools were required.

Parts Used:

Surface Burner Knob

James from Smithfield, VA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Over the years the numbers has worn off the knobs.

Fed-Ex delivered the package and within 10 min I had open the package, removed the old knobs and installed the new ones, My wife was very impressed with the ease of the transactionl. It is good to know that we can still get parts for our cook top even though it is 26 years old. Thanks for every thing.

Parts Used:

Surface Burner Knob

John from Flippin, AR
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

burned oven bulb

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

Parts Used:

Light Bulb - 40W

Ivanka from Atlantra, GA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

3 of 9 people found this instruction helpful.

Was this instruction helpful to you?

Two burner switches had broken

Turn off elec. power at breaker box. Check twice. Removed burner switch cover. caarefull remove wires from switch, note with color to which terminal remove nut on switch replace new switch replace wires to switch, replace cover turn on power. ready.

Parts Used:

Surface Unit Infinite Switch Kit

John from Seguin, TX
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

The contacts on my convertible range top were corroded

I ordered the kit that contained all 4 wires and contacts. The replacement was fairly easy. The only drawback was the tight quarters in running the wires. The job was quick and a success. Now I can use my right side of my stovetop again!

Parts Used: