Models > 4775 > Instructions

4775 Hoover Range - Instructions

All Instructions for the 4775
76 - 90 of 122
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Filter Worn Out
Remove cover and install
Parts Used:
Grease Filter
  • Thomas from Berlin, MD
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Knobs were worn and illegible
Removed the old ones and snapped on the new.
It was a snap and what a difference! Even though the cooktop is over 20 years old, it looks new again. Thanks to the knowledgeable support people at Part Select.Com we picked the right knobs the first time.
Parts Used:
Surface Burner Knob
  • Denise from Huntington, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
needed new grease filter
It was hard. I simply replaced the old one!! fIT PERFECTLY.
:-)
Parts Used:
Grease Filter
  • Barbara from Hubert, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The switch didn't control the heat range
Took the front panel off by removing 4 screws. Then remove the switch by loosing the nut hold it. Then replace the wire on the new the way they were on the old switch. Put the panel back on.
Parts Used:
Surface Unit Infinite Switch Kit
  • Samuel L. from Cardington, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
oven light burnt out
1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes
Parts Used:
Light Bulb - 40W
  • William from Schwenksville, PA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
3 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
replaced oven lightbulb
very easy
Parts Used:
Light Bulb - 40W
  • peggy ann from forest city, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
thermostat temprature bulb hanger clips
snaped them into oven cavity attached temp bulb job complete
Parts Used:
Range Thermostat Clip
  • Dwayne from Atlanta, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
light bulb went out in my oven
My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.
Parts Used:
Light Bulb - 40W
  • Janet from Ada, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The stem of one of my burner switches broke off so I had to replace the switch.
Replacing the switch was very easy. First I unplugged the range to be sure there would be no electrical power to the switch. Then I removed four screws to remove the switch cover plate (located above the oven door). I disconnected the wires from the pin connectors on the broken switch, then removed the switch by removing one hex nut. The new switch was installed by reversing the removal procedure. Took about 15 minutes total time.
Parts Used:
Surface Unit Infinite Switch Kit
  • John from Fulton, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers, Wrench (Adjustable)
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bad switch
As stated on order.
Parts Used:
Surface Unit Infinite Switch Kit
  • Merwyn from Kingsport, TN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers, Socket set
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Numbers on original stove top had become unreadable due to age and needed to be replaced
I originally ordered the knobs that appeared to be an exact match for the ones on the stove top (Part # PS1515077). However those knobs are designed to fit on D post stems. I finally ordered PS48861 which are designed to fit double flat post stems which is what I have on my stove top. New parts fit perfectly. Remove old knobs put new ones on. Total repair time less than one minute. Part Select was great about getting the original parts and replacement to me quickly.
Parts Used:
Surface Burner Knob
  • James from Montclair, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
parts fine,
just inserted in to proper place
Parts Used:
Grease Filter Grease Filter
  • MARY from ELK RIVER, MN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
front burner would only work on high
Installed the part------very easy
Parts Used:
Surface Unit Infinite Switch Kit
  • william from cairo, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven element burned out
The only trouble I couldn't remove the screws that held the wires to the element, so I cut the wires as close to the end as possible and attached new hardware. After that was done it was simple to reinstall the new element. Turned the power back on. Turned the oven on and it worked like new.
Parts Used:
Bake Element with Screws
  • Eugene from Satellite Beach, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
bake element not heating up
removed element and tested wirh ohm meter. No reading telling it was bad. Tested voltage from supply wires. Voltage correct. Ordered new element which can in 2 days. Installed-tested- problem solved. 2 scres connect element.
Parts Used:
Bake Element with Screws
  • john from chatham, MA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 4775
76 - 90 of 122