4448A Frigidaire Range - Instructions

followed the video provided on line which was very helpful..

my original part arrived and it did not fit. When I called to explain the problem I was told it was the wrong part. The big problem is... Frigidaire calls the receptacle a terminal block kit as well as a terminal block kit which is a totally different part. I tried to explain that to several different folks I spoke to at your company as well as Frigidaire but I'm not sure if I got that point across. Take a look at part # 530 393 5058 and part # 530 440 9888 and you will see that they both mention terminal block kit. Hopefully the part I am getting from Frigidaire is an OEM part and will fit.

Didn't get repaired because I could not get the right parts to fix it. You would send me a part for the oven. The oven and burner parts are not the same

Repair was easy. just unscrewed the old handle, holes measured correctly and screwed in the new handle.The only flaw was that it did not come with the two end caps,they have to be bought separately & the handle ends are sharp without them.

Remove heating coils raise stove top unsrew terminal blocks cut wires assemble terminals strip wires twist wires together install wire nuts apply heat shrink lower stove top plug in stove repair complete.Thanks.

Simple: Snip old terminal block off. Strip wires. Connect new Terminal block using twist-on wire caps (provided in kit). Mount to stove top with existing screw. TIP: Make sure you insert the wire lead into the terminal block the right way (not upside down). Otherwise burner element will not insert into terminal block properly.

First unplug the electricity from the stove. Replacement terminals on back of switch are set different than the originals. So, I took notes (purple wire =P, Black wire=L1, two yellow wires = H1 & H2, and orange wire=L2). Your stove might be different in the color coding. Just take notes. First I unscrewed the screws on the top back plate of the stove. Removed the back plate. Took notes on where the wires went. Removed the wires going to the five terminals. Unscrewed the two screws on front panel of the stove holding the old switch in place. Removed the old switch. Put in the new switch through the back of stove. Determined the length of the control shaft. Take the switch back out. With two pliers on the control shaft, holding the pliers closer to the switch firmly, use the second pliers just past the predetermined breaking point. With the second pliers snap off the control shaft. Be careful not to snap off two much. Place the switch in the proper place and mount to the stove. You may need some parts in the assembly parts package for this. I did not. Inside of the parts package is a set of plastic parts. I selected the part I needed to insert into the control knob for a bushing just to take up space. I placed that part inside of the control knob. I then placed it onto the control shaft. Plug back the wire going to the electric outlet. Instead of unplugging and plugging, you might want to switch off the circuit breaker and switch back on when the job is done. It works!

They fit perfectly for this stove. I had bought some drip pans but definitely not the correct pan. Saved time and about same at stores price. Great service thank you will order elements next. Pull heating elements remove drip pans and replace with new pans ,replace heating element. Done

The drawer under the oven had been aggravating me for some time. It was titled and did not close right. Finally, I took it out to see what the problem was and noticed that the glides were broken. I googled the model no. of the stove (figuring I would have no luck) and to my great relief was directed to this EXCELLENT site. I ordered the new drawer glides within minutes and they were literally delivered the next day. Snapped right in, fixed, happy!! It's times like this when I can't figure out how we all lived without the internet!

replaced old drip bowls with new ones

I unplugged the damaged unit and plugged in the new one.

I removed the drawer, removed and replaced the guides on both sides in the front and replaced the drawer.

Just use flat screwdriver to press on clip and just squeeze it in

After researching on what exactly to call the part, which was a front drawer glide. I found this out by watching the video. It showed me exactly what I needed and what it looked like. I run to the oven to look at the other one, to make sure thats what I needed, and it looked like the part that I needed (mind you I am a female, and not a repair person), so this video helped me out alot. When the part arrived, I knew how to take the drawer out, and easily snapped the little plastic glide in to place, and slipped the drawer back on the gliders, and it worked perfect, so proud of myself, that I done it by myself, with no help from husband. I bragged and bragged on myself with a big pat on my own back, thanks Part Select, I know what to do when it happens again. Its my fault cause it broke, cause I overload the drawer with pots and pans LOL!!! Brenda Dixon

Unplugged the element and the melted on pot. Plugged in the new element. I thought I might need a whole new cooktop but a new element was very easy to find online.