41798989810 Kenmore Dryer - Instructions

Opened the top, removed the 4 screws that held the front top the cabinet, took the front off, went after the dust with the vacuum cleaner, lifted the drum, installed the belt, put the front back on, and put the belt over the idler. Most of the time was in the cleaning.

Removed access door. Disengaged spring, removed old idler. Slipped belt around new idler and motor pulley. Difficulty is putting spring back and inserting idler pulley bracket back in place while there is a lot of tension from the belt. Finally used adjustable wrench as a mini hammer.

First I removed the 2 screws on the back. These 2 screws hold the top cover. I also used a flat screw driver to press the 2 locks that hold the top cover, they are located in front and under the top cover . Then I removed the 2 screws that hold the front cover. After removing the front cover I replaced the drum glider and the seal-basket lower. Now my dryer is working perfectly...

I First pulled the top panel up and off from the front. Then, on the inside, removed a square head screw from each side holding the front door panel on. I then pulled off the front panel enough to expose the drum. I then removed the old drum glide with a putty knife, and following instructions supplied with the new glide, glued the new glide into place. I then assembled in reverse order of disassembly.

There was a gap between the drum and the front opening. So, we opened the top of the dryer using the putty knife. There are two clips once you find them you just have to push back on them to release the top of the dryer. Then there are two screws that hold the front of the dryer on. Once they are removed the front of the dryer just came off. The kit has glue and instructions past that point and I just followed them.

First I removed power from dryer. Then I lifted the lid and removed the 2 screws holding the front onto the dryer. I then used a pair of pliers to grip the seal and help pull it off. Cleaned off old adhesive. Recommend getting GOOP BE GONE. Then apply high temp sealant onto area and place seal on top. Press firmly across it to make sure it is in place. Then put it all back together and your done. Also, if upper seal is worn.recommend ordering lower seal at same time. I didn't and should have. Save yourself from doing this twice.

Just like in the video, but with a stackable washer/dryer unit, works like new now....

lacked instructions. Internet yielded a simple paragraph. Scored real bonus when we discovered the lint build up past the internal filter was approaching catastropic level. Replaced the exhaust tube (plastic) with rigid metal and resolved to disassemble and clean dryer on 2 year cycle in future. Kit just isn't complete without detailed instructions. Parts were complete and sufficient. Local codes have eliminated the plactic exhaust tube. Recommend that all old installs refit to rigid or semirigid before the fire happens!

First removed the top of the dryer, then the front of the dryer. Took the plate off the back left of the dryer to disengage the belt off the pulley.
Took the three screws out that hold the drum in place, of course the third screw stripped and had to use a screw remover, which didn't work, but the adjustable pliers did so then lifted the drum out of the plastic reservoir in which the bearing laid. Next unscrewed the two bolts holding the plastic reservoir which also loosened the small metal piece on the back of the dryer where a small bearing is located. Put the new parts in, but instead of putting the larger bearing that fits in the plastic reservoir, I decided to put it on the drum first and guide it into the reservoir all at once, this worked well . Prior to that I put the new plastic piece on the inside and taped it there while holding that piece put the small metal piece with the small bearing on the back of the dryer. I'm sure it is alot easier with two people doing this part, but it worked and I didn't lose the small bearing. Next put the front of the dryer back on and then put the belt back on the pulley, then the top.
It definitely helped immensely to read how someone did this, just follow the instructions given and there you go, no more annoying squeak and also a feeling of accomplishment and thanks to the person who wrote the story on how to do this job, appreciate it.

Moved dryer out where I could get to all sides, then pulled top off, then unscrewed the front panel. The drum lifted out of it's ball bearing assembly in the back with a little force. Then it slid out fairly easy.

I replaced the rear bearing assembly, the bottom drum glide strip, the top drum glide and the vent seal all at the same time. The glue for the glide strips took about an hour to set up and I used clothes pins every 4-6 inches as suggested by someone else here on this site. Then I vaccuumed out the entire dryer body, vent pipes and every nook and cranny.

I put everything back as it had come out and then put the dryer back in it's place. Plugged it back in and it's as quiet as when it was new. Total time of project was about 1:45.

Took front door off, top off, frunt off, removes screws holding rear bearing pivot, and then removed drum. repainted bearing surface on drum, installed parts, let paint dry for a day and reassembled.

remove the top and front of the dryer, then removed the idler assembly. This enabled me to rimove the belt form the drum and replace it and the idler assembly. Not difficult at all.

My husband took the front panel off. We scaped the old seals off. Used the adhesive that came with the drum glide and replaced both parts. No more ripped and stained clothes, that easy!

Unhooked power,shut off gas, pulled top cover off,two Philips screws one on each side hold the front panel in.took belt off, pulled drum,than change out, flame sensor,M coils,and igniter,be careful igniter breaks very easy,I broke my new one so had to use my old one so really the problem with no heat was either the Mcoils or the flame sensor

I popped the top lid of the dryer which has hinges in the rear allowing it to be lifted. This exposes the drum. The front panel then can be detached using a nut driver and phillips screwdriver. The door shut off switch must be then removed so the front panel can be pulled away. I used an adjustable wrench to remove the lock nut. Once the front panel is clear of the drum, the felt and nylon glides are exposed. I removed the felt using a paint scraper, and cleaned the adhesive residue with lacquer thinner. The provided high temperature adhesive was then applied, I waited a minute per the directions, then applied the new felt and glides. The dryer reassembles in reverse of the above disassembly, making sure not to forget to reinstall the door switch. I plugged the dryer back in, and ran a load of laundry in quiet efficiency. Your part arrived quickly, the directions were good, and the dryer now works wonderfully.