41798702891 Kenmore Washer Dryer Combo - Instructions

screwed in the new legs and leveled it off again.

I unpluged the machine. Pried out the old switch with the tip of a screw driver. Pried off the connectors, there was not enough extra wire for me to connect the new switch through the front of the machine. I pushed the new switch in place. Using the screw driver I carefully pried open the top front of the machine { there were 2 plastic spring clips securing the top}. I placed a wash bucket on the drum to hold the top open , connected the 2 connectors to the switch and snapped top back in place.

I noticed for sometime that my dryer had been sqeeking...but I had thought nothing of it. It got alot louder as time went on and then one day the drum stopped spinning. Not to mention I had my son's 5th birthday party in 3 days. So I went online and found parts select. They sent me the whole assembly and I got it the day before the birthday, and it only took me 30 mins to replace it. Thank you, Parts Select for the prompt response and saving me for the embarrasment of having clothes all over the floor.

First I went on-line and found a download for the parts catalogue which contains a schematic for the washer. After looking this over I could determine how to get the washer apart! After getting the front panel off, I disconnected the drain hose from the pump with a pair of water-pump pliers. As I pulled this hose out, water spilled out all over the floor, so I then cleaned that up. Next I connected the new hose and put the machine back together. This job would have cost me over $150 if I had called in a repairman. PartSelect saved me so much money, and I thank them so much!

Basically, i followed instructions on 1 video i seen, but was able to shorten repair by not removing drum, and was still able to access the thermal limiter switch to remove old one and install new one. Worked like a charm. Thanks Dan

First I did some research and concluded the water inlet needed replacing. Obviously once you know what you need you go to PartSelet.com for parts and installation info. I went through the front of the machine. So I removed the front of the washer(2 screws at the front bottom)slide down the panel to separate it, lifted the top cover of the washer(2 screws on the underside of the lid and 3 wire connectors to the fill switches) and then loosened the right side panel(3 screws at the bottom). Now pushing the wash barrel to the side it gave me enough room to squeeze my arms in to the inlet part. Be careful there are sharp edges and screw tips inside the machine. I removed the 2 wire connectors(hot and cold solenoids) inside the washer and then removed the screw from the back outside that holds the water inlet to the machine. Now I was able to pull the inlet closer to me so I could get pliers on the hose clamp to loosen and remove the old part. The new part was an improved version that was more solid. I attached the hose affixed the squeeze hose clamp and pushed the water inlet into place. The screws were not threading so I grabbed a couple of self taping hex head screws and a nut driver head for my drill and screwed the inlet in from the back of the washer. Then I replaced the wire connectors to the water inlet. With the water inlet complete, I reattached the right side panel, the washer lid, fill switch connectors and the front panel. Washer fixed and running perfectly!

Removed the back panel and the exhaust hose.removed the heater element and changed the thermostat wire was melted cut damaged part of wire soldered and rapped with black electrical tap

first i removed the top -second I removed the two screws hold the front on - thrid I unpluged the wiring to remove the front - fourth I removed old part and cleaned off old glue -fifth I applied new glue and new part - sixth I reasembled - worked good as new

the catch on the door was worn and cracked.... so I noticed it could be easily popped out with a screw driver and when the new part came in the mail 2 days later, it was just as easy to pop back in with no tools required. Now the door stays shut really good!!!

removed top and front panel on stackable dyer unit. 3 screws at back of the inside of the drum, and the drum was out. installed new bearing and belt and all was good.

I took off the front panel of the washer and placed the belt on the large tub wheel and then the smaller wheel. I placed the belt over the adjustable third wheel and turned the tub in order to get the belt all the way in the grooves. Thirty minutes max to replace. Thanks, my order was 100% satisfactory

Removed old filter, installed new filter

Removed top,removed hose from inlet valve to washer,removed hot and cold inlet hoses and with phillips screwdriver removed water inlet valve assy and replaced. Reassembled and tested.

My order arrived 2 days after i ordered same. Excellent service from partselect, Thank You....

The hardest part was getting to the part and removing it and putting it back on. The schematics that you had on your website helped us locate where it needed to go and, hopefully, that will solve our problem.

From previous responses on this site. I just followed their lead. If I had not found these folks, and the responses, it would have been a nightmare. It looked like and I thought the dryer came apart from the back! But in reality it comes apart from the front!! Absolutely fantastic site and help. Fast shipping, I ordered on Wednesday before Labor Day, didn't expect the parts until the following Wednesday, but received the parts on Saturday morning, and had the dryer back running by Sunday AM. Never even ran out of clean clothes!!!!!