41549 LG Washer - Instructions

Unplug washer!!! 1. Remove retaining ring around rubber gasket with flat head screwdriver. Just slightly pry off and it will easily come off. 2. Just peel back rubber gasket on the side that the lock is on. 3. remove 2 screws from the front off the lock assembly. 4. gently reach in and lift the little plastic clip holding the wiring harness and lift straight off. If the clip is lifted it might be a little tight just use even steady pressure to pull off. 5. Reverse these instructions to replace. Note: replacing the retaining ring on the rubber is a pain. The spring has to be in the bottom. Using a couple of flathead screwdrivers you can wrangle it back in place after awhile. There is a tool that looks like a large reverse pliers that may make it easier. Anyway thats it, pretty easy. There is a youtube video that shows all of this.

took out the drain pump and replace with a new one

During my troubleshooting, I removed the bottom to access the drain pump. I had to cut some wire ties so that I could make removing the wires easier. After checking the pump and putting everything back together, I determined that the pump itself was bad. Pump impeller should not rotate freely! After receiving new part, I installed it relatively easy. I didn't have to remove the bottom since there was enough room through the access hole. Just make sure to make where wires go before removing old part.

It was so easy. i searched my model it brought up this site and the most common problem popped up without my even asking and recommended the part. i got it one week later and it was so simple to fix. a repair man wanted three times the part price to come to my home twice and would have had to wait longer. you guys were very helpful

The problem ended up being the pump motor which discharges water from the washer. I figured out this was the problem after trying several things. I determined the motor was fine when it was empty. With the unit turned off, if you can rotate the tube with a quick spin and it lights up, probably this is OK. Then I tried to run it again and it went about 1/2 way through the cycle and stopped and started humming again. So I started emptying out the water, which I noticed was about 5 gallons which is way too much. so once empty, I took the pump off by turning unit on side. There are two hoses with hose clamps, and a few screws. Be careful to mark which wire plugs onto which side of the pump. One is brown and one is black. If you take the pump housing off, with the 3 screws, you should be able to pull the motor apart. Mine had water and scum from the wash in it, which was a dead give away that it was the problem.

new pump was a little different ,but mounted properly. Tipped washer on its side, changed pump by working trough bottom and back access. It went pretty smoothly, works fine.

Removed the old bellows (2 squeeze hose clamps and one screw adjustable hose clamp) slid on the new one and it was done!

Another friend of mine did the repair.I watched him remove the old Drain pump and Motor Assembly and the Circulation Pump Motor.He installed the new parts in 45 to 60 minutes. The washer works like a new one. I had never ordered from Parts Select before. I was amazed how fast I received the new parts. Order placed on line on Friday , received the order at my home on Saturday afternoon.I will tell my friends about Parts Select and I will buy from them in the future.

1) Shut off water supplies 2) Unplug 3) Disconnect water supplies from back of washer -some water will dribble out 4) Unscrew 2 screws at back of washer top plate (the lower of the two screws on each of the plastic bumpers) 5) slide top plate back a couple inches, then lift off. 6) Carefully stuff a towel underneath the distribution hoses and valves to catch any water that escapes during replacement. 7) Snap a photo of the entire area to help identify where the hoses and electrical connections are located to aid in re-connection (or label with tape). Be sure to note the color coding on the wires in relation to how they connect to the valves. 8) Pull the electrical connector(s) off the valve assembly 9) Use pliers to loosen and slide the hose clamps off as many of the hoses as possible and pull the hoses off the valve assembly. Some hoses are hard to reach, and can be removed after the valve is detached from the washer housing. 10) Unscrew the two screws from the back of the washer body holding the valve in place. 11) Remove the valve (and any remaining hoses). 12) Attach distribution hoses to new valve 13) Place new valve into washer body and screw into place. 14) Reattach electrical connection(s). 15) Remove towel and check for any stray water 16) Place top cover on washer and slide forward to lock in place. 17) Replace screws in top cover at rear of washer (unless you plan on checking for leaks after testing) 18) Reattach water supply hoses 19) Turn on water supplies 20) Plug washer in 21) Run washer self-test to check that all water inlets operate -see note at end 22) Check for leaks at water inlet hose connections and underneath washer OPTIONAL but ADVISABLE: check for internal leaks - 23) Unplug washer 24) Remove top cover 25) check for leaks at distribution hose connections 24) Replace top cover 25) Secure screws in top cover 26) Plug in washer NOTE: Washer self-test instructions: Turn washer off. Press and hold the SPIN SPEED and SOIL LEVEL buttons simultaneously, then press POWER button. Keep holding SPIN SPEED and SOIL LEVEL buttons until buzzer sounds twice. Release buttons. Press START/PAUSE button 4 times to test prewash inlet and listen for sound of water entering the washer. Press START/PAUSE button again for main wash inlet, press again for hot inlet, press again for steam inlet, press again for bleach inlet. Press 4 more times to get to drain cycle and watch for water to drain from tub (if any visible). Press 3 more times to turn test off. Power off washer to reset.

Hardest part was getting the correct part. Due to some glitch somewhere there was a mix up in the database for the correct pump number. This unit has two pumps mounted to the same housing. One is a recirculating pump and one is discharge pump. I ordered the discharge pump and kept receiving the recirculating pump. Discharge pump is LG PART#4681EA2001T and recirculating pump is LG PART #4681EA2002H Once in hand the install went fairly smoothly. Removed top - two screws on back of unit. Removed control panel with one screw on upper right inside corner, associated plugs and snap clips. Removed soap tray and drained water through filter tube. Removed screws in front of filter. Using Vise grips stretched spring from around front seal. Removed screws holding front of washer to top frame (2?)[accessed after soap tray removal]. Pump assembly located in bottom left, removed associated hoses, Marked wired colors on pump housings and removed. Removed assembly. Unscrewed pump, installed new pump and reversed procedure to reassemble. Struggled mostly with replacing spring around front seal. Stretch it as far apart as you can as you "roll" the spring in and then massage the seal to get the spring into correct position. Definitely a doable repair. Good Luck.

After checking for blockage on the drain hose and checking on any blockage on the bottom left corner filter and not finding anything i decided to open the machine. Everything suggested a broken drain pump
ITEM
PS3579318 Drain Pump and Motor Assembly which is located on the bottom left corner also and it attaches to the bottom left corner filter. And voila! The machine did not work! Now started throwing a FE code and it would not fill up. Well, the new pump was stuck! All i had to do was to stick my fingers in the bottom left corner filter orifice and move the fan like devices that make the new drain pump work, that did it! Be careful not to do it while the machine is pluged in, those plastic blades may hurt your fingers. To reach the drain pump you have to take the top, control board and front (door and gasket) of the machine off, about one hour labor.

Replaced the 4 valave unit and single hot water valve at same time. Unplug unit, remove two plastic tabs on back of washer, push on top from front to losen. tur off both water valves, remove two screws holding valves in place, mark with tape which hose goes to which vavle, < back left, back righ, front left, front right, and write in electrical plugs the same. Hot water vavle is by itself, mark it anyway>. install new vavles, replace hoses, and eletrical plugs on top. Make sure clamps are all the way forward and tight! > leave top off. turn on water and electrical, run one short cycle to check for operation and leaks, if ok, replace top and back screws. Simple job, saved me $375.00 doing it myself.

Basic skill

I received the part needed within a few days from ordering. I immediately removed the leaking part with the new part. It was a very simple install, and my washer is now leak free. If you think you cannot do these simple changes, think again, it's much easier then you may think. Remove the top cover of your washer machine by taking off the two screws in the back. Remove the hose clamp with a pair of pliers and pull off from the intake valve, of course make sure your water valve is shut off before starting. Remove the two prong clip. Using your pliers, disconnect the main hot water hose. Use a Phillips screwdriver to remove the two screws that holds the valve in place. Remove and discard it and replace with the new valve. Follow the steps and your done, it's that easy....TC

Used a screwdriver to carefull lift the top of washer. Reached in and unplugged old assembly from wir harness. Unscrewed old one (2 screws) from washer screwed in new one connected it to wire harness. Closed top of washer and plugged it in and it was ready to use. I am a 53 year old female and had never done this before. The repair shop wanted $150 to install part plus the part cost more from them. I' m sure a guy could do the job in 15 minutes or less.