41182 LG Washer - Instructions

I unplugged the washer, and removed the top of the washer by removing the two screws securing the top to the washer. You'll find them inside the two plastic pieces on the rear of the top. Remove only the bottom two screws in each plastic piece and slide the lid to the rear a few inches then lift straight up to remove the lid. Disconnect the water hose from the rear of the inlet valve assembly then remove the two screws in the rear of the old water valve bracket that attach it to the washer. Pull the old unit inside the washer and set the new unit on top of the old. Swap over the electrical connections to the new water valve assembly, matching the locations where the connectors were originally. Then swapped over the water lines from the old unit to the new unit using common pliers to compress the hose claps. Finally, attach the new unit to the washer with the two rear screws. Replace the water hose and the top, and the unit is ready to test.

Removed the old bellows (2 squeeze hose clamps and one screw adjustable hose clamp) slid on the new one and it was done!

The machine was making a grinding noise instead of draining. I spoke with the LG rep on the 800 line and was told to call a repair man. The Parts select diagram helped me to identify the part I needed. It was clear enough that I was confident it was the right one. Three days and six screws later the machine was working fine.

Ordered a new water valve, easy installation, removed top cover of washer. Two screws and three hose clamps, done in 20 minutes.

removed 2 screws on back. removed top. disconected wires and hoses removes 2 screws holding assy in place and removed assy. put in new assy and installed hoses and plugs in same location removed from. reinstalled top and hose and ran washer.. new valve unite works but has a high pitched whine when valves turn on. :(

The difficult part was finding the leak since it was very small and the washer was completely wet around the frame at the bottom. After completely drying everything off and waiting an hour-nothing.I had assumed the leak was in the bottom area around the hoses when actually the leak was the cold water valve[top rear] seeping,then dripping on the drum and dripping onto the frame 8 inches away.I ordered the valve about 10:30am online, the next day at 1pm it arrived. Very easy to install in 15 minutes.

Hot water valve was leaking when washer was not in use and flooded floor. Advised owner to replace hit and cold water valve same time since only hot valve was bad. Hot water was easy but cold was difficult because it has the bleach and softener valve attached in one unto with three hoses and three wire connections. The opening at back of machine was small and you must have small hands to replace them. If not, then you have to remove top cover to get to it which is extensive.

The repair went well and your parts are easy to find. This is the second time I have used your services and both times have been great. Your parts are at great prices and your delivery is a lot faster that one would think.
Thank you

Unplugged the washer,removed the rear cover, removed the old rotor assembly & installed the new rotor with thread lock on the retaining bolt.

pulled off top of washer to get at the inlet valve disconnect two hoses take two screws out and then you put it back together the way you took apart and your done

First we unplugged the machine. Then turned off the water and disconnected the hoses. Pulled out the machine and laid it on its side to access the themsistor located on the drum. (No, you do not have to remove the control panel at all to replace this part) The thermsistor is clearly seen with a flashlight. There were plastic ties holding the wires of the thermsistor so we used small scissors to cut the ties. Then unplugged the old thermsistor and plugged in the new thermsistor and used a regular bag twist to secure the wires. Repair complete and the machine is back to normal. Thank you Part Select.

After finding you on google it was easy to repair. It saved me $95.00 service charge. Your direction made it very easy.

removed top, removed 2 screws, replace part. did not fix problem, the real problem was the water inlet valve, works great, easy fix. thanks

Removed lid (top of washer), then ran a cycle in normal to identify the failed component, then noticed the water inlet valve assembly for the hot water was leaking, used my pc and went to website Part Select and found to failed part on the parts break down item, then ordered the part, the part "Valve Assembly Inlet" for the hot water arrived 2-days later, replaced valve in less than 5-minutes, disconnected push on electrical connector, unscrewed the valve assembly inlet and installed the new valve assembly inlet, very easy

Unplug Washing machine first. Then remove 2 screws at the back of the top cover. Slide the top cover back then lift and remove. Unplug electrical connector @ inlet valve and remove water lines 1 going in and 1 out of valve. Remove 2 screws holding assembly in place then install new valve assembly and all other components in reverse order.