40290118 General Electric Dishwasher - Instructions

Unscrew old stripped out one and put in new one ..wala!! Easy repair for this old lady...

Ordered a new basket it was a little large as I ordered the wrong size. I just broke of the tabs that held it in and now its perfect and larger !!!! Simple and great service !!!

Original part no longer made. Substitute too small by a half an inch. Corrected the problem by removing the 4 corner wheels from the old rack and put them on the new one. Now, it fits and works perfectly.

Dishwasher had become noisier & noisier in last year during wash & rinse cycles. After looking at various web sites, decided to first pull motor/pump & try cleaning it out. That made no difference. Also looked for anything loose that could cause vibration. No change in operation. Decided to go for replacing motor/pump & found Part Select had best price. Part came next day! I was amazed! Looked at video, then removed old unit and attached new one. Easy because it was exactly same connections. Ran dishwasher and it sounded 100% quieter - like when new! Very happy!!

Dishwasher had flooded. Removed Dishwasher from cabinet and diagnosed problem. Found "PartSelect" on Internet and found Part kit available at reasonable price, in stock to ship immediately. Part #PS260801 [WD26x10013] contained enough parts to make installation easy and also I was able to cure discovery of slit in drain hose that attached to dishwasher drain outlet because kit included a short piece of hose and a hose clamp that allowed hose that had been trimmed to connect to outlet.

On this model the panel under the door can be removed by unscrewing two hex screws on the upper panel and two phillips head screws on the lower vent panel. The drain solenoid is located on the left side of the pump and can be accessed easily without pulling the dishwasher out from under the counter. The solenoid is held in place with two phillips head screws, and the plastic actuator that is attached to the valve stem is simply press fitted on and held in place with a retaining ring. All necessary parts are included in the repair kit.

I took the dishwasher out from under the sink and looked at the pump and motor, saw that the cooling fan that this old style motor used was broke. Ordered this kit and installed it. I didn't even look at the directions that simple of a swap. Thank God!

Followed the directions. I've done this before. I used to fix these things for a living. The metal clip in front of the seal wouldn't come off. I ended up pulling the shaft out of the drain flapper in the pump which ruins the pump. A 14 year old DW isn't worth a pump. So I bought a new KitchenAid. The seal should come with a new metal clip since you may have to destroy it to replace the seal. If you are buying a seal, buy the clip.

The motor/pump Kit I purchased could fix/be installed in any GE dishwasher made since 1970. I would guess that the one I have is about 15-20 years old. I encountered only one small problem with the kit------ a motor hanger that had to be bent a bit to fit correctly. Other than that it was a total breeze. The clear instructions included in the kit helped quite a bit. In 30 minutes or so ,I was done and our machine was back in operation

Followed easy instructions and completed repair in less than 30 minutes.

Remove the retaining screw in the top of the hub and install new hub in reverse.

Dishwasher is 22 years old and I'm 80 years old so it took longer, about 3 hours. After removing, turned upside down and removed old pump-motor assembly and replaced with new following directions [which took a little while to figure out; my assembly was quite a bit different from the replacement pump-motor]. Pleasantly surprised at how quiet the dishwasher now runs. Normally I would replace this old an appliance, but this unit has provision for inserting a wood panel that blends with the cabinets and a new GE dishwasher with this feature costs $1300 MSRP. I'm trying to save money for when I get old so I decided to do the repair myself. For $150 it was a worthwhile investment.

Most difficult part of repair was getting dishwasher out and in under the cabinet. Especially, feeding the copper water line from under the sink and then back while trying to align the connection. Installing the part itself was easy with good instruction for taking it off and reinstalling. However, since the motor had been upgraded, it required new connections. The connections were provided for this, but no instructions for the electrical connections.

This was really easy. The parts fit perfectly. First i turn off power at circuit panel; turn off water and dissconnected water line and discharge hose. Removed dishwasher from under counter and placed on side. Disconnected connections to motor and pump and replaced and installed same as one unit.

Too easy- what made it easier was this is a portable roll-around unit I could lay on it's back. Loosen the two clamps around the washer pump, hook up the drain solenoid, washer motor wires, attach the motor hanger, that's basically it. It took longer to make sure I was working from the right set of instructions- this pump covers several models. Once I had that right, it was really a snap. Now the unit is so quiet. It once sounded like a jet engine in the kitchen, now it runs so quiet you can hear the water splashing around inside- a big improvement. We should be able to hang onto this thing for a while longer.