40290117 General Electric Dishwasher - Instructions

Since the pump and the motor was a single unit, I removed the assembly by disconnecting the electrical plugs and drainage connections. This was a very simple installation. I reversed the above steps, reinstalled the dishwasher and all worked out well.

First I removed the dishwasher from under the counter. I turned it onto it's side so I had access to the motor and pump underneath. I determined which version of the old pump I had. I removed the old part and easily installed the new motor/pump following the directions. It took a little while for the water to begin flowing when I started it back up. Eventually it did get going.

The repair went smoothly. There were actually instructions included with the parts, so that was nice. The only "gotcha" I found was that . . . after you take off the old food-chopper, you have unscrew the old impeller from the motor shaft. This was a bit difficult and you'll want some good pliers to do it. Don't worry about stripping where the food chopper screwed on-to, that part is attached to the impeller and there is a new one on the new impeller. When I re-installed everything onto the dishwasher, it rattled the first couple of times while the wear-ring was finding it's seat. Don't worry, that's normal. It went away by the third wash. I think I still have a small crack in the pump housing, though. The pump housing is two halves of molded plastic fused together along a seam, and I think the seam is starting to leak. It's about one drop every 45 seconds. I'm thinking JB Weld will fix it.

Opened the package and screwed in the new rinse aid fill cap. No problems. It fit and works just fine.

After disconnecting the supply and drain hoses I unscrewed the security screws and slid the unit out of it's space under the counter. I tipped the machine about 30-45 degrees to one side and examined the underside. I noticed a solenoid that appeared to control a valve leading to the drain tube. I cycled the washer through a wash cycle and noticed that the solenoid never activated. I removed the solenoid and found it filled with debris. I cleaned it out and reinstalled it, but it still did not function. I ordered the part from PartSelect.com because they had the clearest description of the part I needed. Delivery was quick and installation took only a few minutes. After hooking everything back up and sliding the machine back in place, it works like new.

Replaced with a new rinse aid fill cap.

Once the new motor and pump kit arrived. I removed the dishwasher, turned it upside down and replaced the motor and pump with the new one per the directions. Difficulty came in feeding the electrical wire/plug back through the cabinets. Once done, turned on the dishwasher, filled the tub, then manually moved the dial to drian. The water still would not drain from the tub. I searched further for the problem. Here it is; Found the air gap tube was plugged with food. Once I removed, cleaned and reinstalled the air gap, the tub drained fast and everything works great. So, I hope you folks put this up in your troubleshooting section for others to check before buying a pump and motor kit. If you had, I would have been able to check out the air gap, clean it out first before spending $140.00 for a pump and motor kit I didn't need. Anyway, lessons learned..Jeff

I simply removed the front toe kick panels.
The solonoid is staring you in the face.
I removed the small nuts on back side of the solonoid bracket and removed the retaining clip and springs.
I installed the new solonoid and was very surprised how easy it was.

I DID turn the power OFF at the breaker panel prior to starting the repair.

Unplugged unit, unscrewed screws on top of dishwasher attached to countertop, undid water supply and drain hose that goes into tee with garbage disposal. Using crescent wrench turned front leveling screws up all the way and slid/rocked dishwasher out from under the counter - I had no problem leaving back leveling screws down. Turned dishwasher over on some towels (it WILL leak some water so spread out some towels!) so it was oriented like the directions that came with pump and motor. The directions were good, although color or a picture might have been more helpful. CHECK the new pump/ motor unit CAREFULLY for any loose debris from packing etc. I had a small piece of plastic that was in the top of the motor that goes in the dishwasher bottom that rattled around after I installed everything and put it back. I was able to get to it from the drain assembly in the tub but it made a heck of a racket at first. All in all, I had a great experience. I'm glad I ordered the pump and motor even though I only thought I needed the drain solenoid because when I took the old unit out, the prop on the old impeller was almost gone. Easy to order, good customer service (I called with a question and talked to a wonderful customer service representative!), good directions and easy to do. I'd say a 4 out of 10 in terms of difficulty. Thanks PartSelect!

Only getting "humming" sound from dishwasher. Although water had filled the dishwasher tub, pump/motor would not operate. After some research, figured the motor had siezed and I had to replace the pump/motor assembly as mentioned on this site. The kit came in a couple days and I reserved a Sunday afternoon for the repair which I had never done before. Hardest part of repair was unhooking and removing dishwasher from under counter and then getting it back in proper place. I would suggest providing some instruction within the repair instructions showing how the dishwasher is installed or how to remove it as I had never installed one so I was not quite sure what screws etc I needed to remove on the dishwasher itself to start to remove it? I was able to find the original installation instruction for the dishwasher and found that all you had to do was remove two screws from the inside top of the dishwasher which were securing it to the bottom side of the kitchen counter and then the whole thing just slides out. Once removed, turned dishwasher over to access bottom where pump/motor is located. After determining which diagram to use with the instructions, proceeded to replace the motor/pump assembly. It came out easily after wrestling with some corroded bolts/nuts and the existing pump inlet and outlet hose clamps. Mine were old and worthless and no new ones (3-4") are supplied with the kit. Had to run to hardware store to get new hose clamps for the inlet/outlet of the pump before intalling new one. Suggest new hose clamps be provided with the kit. Only thing that was not too clear in instructions was when reconnecting power wiring harness to motor. By looking closely at the instruction diagram I was able to locate what looked to be the right power extension harness from the bag of parts and attach it to the existing power wire harness and the new motor. Suggest also that you somehow better distinguish or identify the proper way the power wire harness should be fastned to the motor? The existing power wires were both the same color and both the female and male connections for the power at the new motor were identical leaving you to guess which wire goes to which connection. After re-installing dishwasher, put about a gallon of water in bottom of unit prior to starting and then put it through a few cycles. It has been working just like new. Suggest having a helper when removing and re-installing dishwasher from under kitchen counter to assist with the power cord, water line, drain line, and help to turn the dishwasher upside down and right side up again.

Disconnect water line and screws (2) holding dishwasher under cabinet, and clamp for wastewater line. Pulled dishwasher out, turned on its side, and removed pump. Disassembled pump per instructions (great instructions) and installed new parts. Reversed to reassemble and except for a loose clamp that leaked (I tightened) it went well. Just under 1 hour.

Turn off power at breaker box.
Remove lower covers and 2 screws into counter top.
Verify sufficient length on water and electrical connection to allow sliding dishwasher out approx. 2/3. I disconnected the electrical at the j box on the dishwasher. If you must disconnect the water line, shut off supply, usually located under nearby sink, and provide a rag or sponge for small amounts of water left in supply line.
Carefully pull back the insulation to expose two screws on top where water line runs into the center.
Pull the top tray part way out and reach in to hold the spray arm while removing the screws. The spray arm will easily drop out.
Hold the new spray arm in place making sure the raised screw posts push into the holes, then reinstall the two screws. Done. Pull insulation back into place, retape if necessary. Reconnect electrical and water if necessary.
Slide unit back in, checking alinement. Rescrew to counter top and reinstall lower covers. Task complete. 15 mins if prepared. 30 mins if both elect. & water are disconnected and you are somewhat hesitant.

First I opened the package and screwed the new dispenser cap into place.

I just plugged in the model number and a screen came up that showed all the part numbers that made up the model. picked out the parts that we needed and ordered it and within 2 day we had the new basket that we needed for our dish washer.
the service and ease was better that going to the appliance store and picking up the basket.
I was very happy the the service.
Donald Brown

Read directions. They were poorly drawn. Set them aside. Opened up unit on December 26th. I made careful observation of the wiring, two hoses, one metal bracket, the hose two clamps, and then proceeded. Instructions said 1 to 2 hours, to complete. Ha Ha, perhaps if you've done it before. It was actually really closer to four hours. When done, it worked perfectly. The best part, my wife said: "This was the best Christmas present ever!" That made my day! Dishes are clean again, just like new! Thank you: www.PartsSelect.com.