3KSM150PSTGA0 KitchenAid Mixer - Instructions

I watched the university of YouTube videos, and followed their instructions.

I did exactly what the PartSelect video demonstrated after watching other DIY videos on the Internet, thus I did not remove the stand which seemed like a little too much for a simple straight forward repair. This is the second time I have replaced this gear. The first time was about 10 years ago when the bakelite gear broke on a 30 year old KitchenAid K
-45. That mixer made hundreds of loaves of bread after grinding many pounds of wheat berries. The only reason we had to replace it was that it walked off the flour dusted counter and landed on its head when my wife had her back turned. Otherwise we would still be using it. :-)
Thanks for the excellent service and instructions.

Used youtube movies to disassemble the mixer and found that the gear was stripped. I kept the screws in labeled ziploc baggies so I wouldn't forget which screws went where. Once the part arrived, it was very simple to replace the gear. I regreased the mixer and then reassembled. The trickiest part was how greasy everything was! It was also hard to get the pin through the beater hub - I found a video that suggested using a very slim screwdriver to thread the hole before inserting the pin. This was the most involved part replacement I've done on my own, and it was very satisfying to get my mixer back in working order!

Replaced gasket and O-ring. Problem solved. POC (Piece of Cake).

The new part was too large for the replacement job, but we used the self tapping screws that came with the mixer and screwed them in from the bottom to open the holes a little more since the original screws were to short to hold the new plate. Then we replaced the screws with longer screws and that seemed to do the trick!

I watched a short video on replacing the worm gear, although I did not know what the problem was until I watched the video. after the video ended I took the mixer apart and found the problem located a parts number an placed my order. got the part in one week put in the new part in about 20 minutes and it work like new. and the price was very reasonable

I simply inserted the new beater into the mixer to see if it scraped the sides of the bowl. It fit perfectly and didn't scrape the bowl like the old one did.

Repair is very straight forward. Remove the existing plate by removing the three phillip head screws. Use a regular screwdriver or knife to pop the plate off. (I cleaned the area while I was there but probably not necessary) Position the new plate with the screw holes lined up. Press down to pop the plate into position. Install original screws and tighten. You're done!

Removed old plate, screwed in new plate and works like new! Was so happy I wouldn’t have to replace my 30 year old mixer.

Went to partselect, found model number, printed blow-up of mixer. Figured out disassenbly procedure. Drove out main pin removing mixer head from stand. Save pin. Drove out pin in mixer main shaft which allowed planetary head to be removed. Save pin.
Removed stainless steel bezel to expose screws for removal of bottom half of mixer body. Removed screws and carefully separated mixer halves using two screwdrivers as prybars. Care must be exercised to prevent chipping of paint on body.
Separated body. cleaned grease from gears to find actual problem. Removed broken geartooth and grease near broken part to make sure no small broken chips remained. Removed pinion shaft assembly, drove pin from gear releasing broken pinion/shaft. Save pin/
Cleaned grease from pinion shaft assembly using mineral spirits and a small brush to reveal how part could be disassembled. Ordered part immediately on-line. Part arrived 1 business day after it was ordered.
Reversed process for replacing pinion shaft. Applied fresh grease obtained from excess already in mixer, spun pinion shaft to make sure grease was properly distributed. Reinstalled pinion shaft assembly. CAREFULLY plugged in mixer and jogged motor to make sure all was free and that mixer worked. If you can repair this mixer, you should have enough sense to do this diagonistic. Keep fingers away from all moving parts, don't touch expposed electric wires. Plug in only after making sure switch is in off position. Jog using mixer switch. Make sure mechanism is free.
Complete re-assembly by following blow-up and reversing disassembly steps. It may be good to write down you disassemblly procedure if it is possible that you won't be reassembling within a day or two.

Removed the rear cover to inspect the speed board. Replaced motor brushes and noticed the motor body nuts were loose and 1 was completely off. Cleaned up speed board and replaced the motor body nuts, tightened with nutdriver, adjusted speedboard governor screws and with new motor brushes worked like a charm. The very rough sounding motor noise was gone and the mixer has not operated so quietly ever.

Followed web site's videos. One step left out of video.

Took each area apart. Replaced the gear and reassembled it.

replaced gear, and brushes.

watched how to repair