38487KBRDRCC General Electric Refrigerator - Instructions

removed freezer panel,found the evap.iced up,put defrost timer into defrost. wated five min.no heat used hair dryer to defrost evap.found termination visually defective.replace defective part.no call back.Iam a EPA certified universal technician.

Because the kit did not include fasteners, had to use wood screws and superglue.

Replaced above parts and the noise problem was not resolved. Ordered a new motor, fan blade and another set of grommets from PartSelect. The parts were delivered the next day. Took me about 15 minutes to swap the new parts in. It's been 3 days since the repair and the noise has not returned.

HI I am Stoyan. I had a problem with my refrigerator. The freezer produces a lot of ice, but the refrigerator was warm. I try to find what other people comment on this site partselect.com. I decided that the thermostat is damaged. I ordered the thermostat from partselect.com and I had the delivery within 24 h. and I was very happy with the fast delivery service .I saw a video on the same site how they show how to do myself the change of the thermostat. I took the hairdryer from my wife to defrost the refrigerator for 40 minutes and removed the old thermostat. I decided to test the heater with a 9 volts electricity from a portable charger for a car. I made an electric circuit chain and on the end of the heater I saw that there was 9 volts electricity and I understood they are ok. I changed the thermostat for 5 minutes, looking very carefully to match the colors of the cables. For $ 11, I saved money to buy a new refrigerator or pay a big bill to a repair service. Thank you for the video that helped me very much. My refrigerator work well.

I used the socket set to remove pannel that allowed me to have access to the evaporator fan. Once the fan and it's container was visible, I removed the entire fan container using the socket set. I took the fan out of the container, removed the damage blade and the damaged fan grommets. I then replace the old blade with the new blade and put the fan and the compartment back together. I am not very handy so if I am able to do this, anybody can. Ps. I was very very pleased with the services I received from PartSelect and would encourage others to use them - must admit I was very suspicious at first.

Defrosted the refrigerator,power off and cut the 2 wires on thermostat and sodered the new one on and shrink tube sealed the wires,refrigerator works like new!

My fridge came with only a single snack pan, and since the glass shelves are identical I decided to order the parts needed for installing the second snack pan. The glass shelf is secured in front by a round plastic pin protruding from the side of the fridge. Once the shelf is lifted upward and free of this pin, the rear retaining ears on the metal shelf side brackets can be released from the vertical-slotted metal track at the rear of the fridge. Make certain that you have the Right and Left snack pan slides oriented correctly, and positioned on the correct side of the metal shelf brackets. You’ll need to thread two self-tapping screws into each of the snack pan slides: one near the front, and the other at the rear. These screws extend through the metal side brackets into pre-aligned holes in each pan slide. When this is completed, you can test-fit the new clear plastic pan slide (drawer) into the slides to make sure it fits correctly. All that's left to do is insert the retaining ears into the appropriate pair of slots at the rear, then lower the front of the glass shelf until it's properly positioned over the plastic support pin. Now you're ready to enjoy twice the snack pan capacity as before!

Remove back cardboard, slide clip off that holds capacitor in place then unplug. plug in new parts replace clip and back cover and your done! refrigerator works great again thanks for quick shipping as well.

per your instructions

took the old stop off put the new stop on

I started at the compressor and replaced the overload and the Ptcr first and that did not make the compressor start running again, so I replaced the capasitor and it still did not start, so I bit the bulett and replaced the Main Control Board and that is what I should have checked first, when I removed the old one I found a little burnt spot on the back that I could not see from the front. The new one did not look exactly like the old one, it had two more wire terminals than the old one, but just leave them blank and everything will work just fine!

replace the bar lift top off

Had a similar situation with a central A/C unit and the capacitor was the culprit. Went online to Parts Select, punched in my model number and Parts Select brought up the detail breakout of my unit. I easily identified the capacitor and the overload unit it connects to and ordered the parts for about $40.That whole process took about 10 minutes. Replaced the parts in about 15 minutes and cured the problem. Parts Select was so easy to find and order what I needed that on a scale of 1-10, I would rank them as an 11!

removed the inside fridge electrical panel and swapped switches

easy pry out, disconnect wiring, connect on new switch and press in switch.