3639715921 Kenmore Refrigerator - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
no ice
-
Richard from Las Cruces, NM
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
would not make ice
i watched the free video and then made the switch my ice screw had 4 bolts instead of three that was the only difference used the screw driver to loosen the straps on the connection plug and that was it easy as pie in about 30 minutes i heard it drop a load of ice it beats filling ice trays all the time thank you partselect for the free video it was the difference in my sucess
Parts Used:
-
jeffrey from clinton, TN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Gears were jammed, and broken when jam was cleared causing them to make loud knocking noises when spinning
Popped off the old gears with a screw driver. Put on the new gears with a screwdriver. Problem fixed in less than 5 minutes.
Parts Used:
-
Nathan from Coralville, IA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Was not making ice
Took old part out , put new part in. Was so easy thought we did it wrong. Ice maker working great, have lots of ice now. Thank you. Colleen
Parts Used:
-
Colleen from Yorba linda, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Ice Maker stopped making ice.
Ice maker was side mount instead of rear mount as shown in previous insructions. Removed one screw and slide ice maker forward. used flat head screw driver to undo the ice maker plug. The ice maker came right out. Removed old ice maker fill cup and put it on the new ice maker. Slide the new ice maker into place and used the same screw to secure it. Pluged it in and turned on the ice maker. Had new ice in a couple of hours. It comes with a round plug to square plug adapter, new fill cup and fill tube, all of which I didn't use.
Parts Used:
-
Charles from Edmond, OK
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Was not making ice cubes
Only needed to remove one screw, slide unit out and disconnect the power cord. Theb reverse the above operation to install the replace ice maker unit. Quick and extremely easy....
Parts Used:
-
Bob from JASPER, GA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Ice maker quit makeing ice
Wathched the video and it was done in less than 15 min making ice again no problem
Parts Used:
-
Dickei from Sugar Land, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
ice maker not working
unscrew one screw unplug.insert the ice maker,put the screw back in you have ice less than ten minutes
Parts Used:
-
Garry from San Antonio, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
No ice!
Literally took out one screw and a wiring harness. Removed the old plastic piece off of the old ice maker and put on the new one.Installed new ice maker with the one screw and plugged the wiring back in.DONE!
Parts Used:
-
Jacob from Waggaman, LA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
left side rail broke in half middle support broke at front end
As instructed actually my wife ordered the parts and
Installed herself. Positive experience.
Installed herself. Positive experience.
Parts Used:
-
JOE from INDIAN ROCKS BEACH, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Cord
-
Laurie from Portland, ME
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
slide rail broke (after ten years of use) when I yanked it too hard while cleaning the fridge,.
Ordered a new one and watched a YouTube video on how to do it. Really didn't need it, but it was a nice touch by Part Select because it made the repair go faster than it would had I not seen the video. All it took was one screwdriver, which is what the video said, and a little aligning of the side rail with the from piece. Screwed it together (2 screws) and that was it .
Parts Used:
-
Ronald from Marlborough, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
No ice.
-
Jim from Reading, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
drawr slide broke
-
Beverly from St Louis, MO
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
right side slide rail broken
pull the front cover off, take the two screws out and the side rail comes right off, put the new one in place, put the screws back in and bang!.....all done. Took longer to take the stuff out of the fridge than to make this repair.
Parts Used:
-
Keven from Fleming Island, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!