All Installation Instructions for Kenmore Refrigerator 3639565550

Small grate on my ice dispenser broke

through away the old grate. Then put the new grate in the depression All done.

Parts Used:

Dispenser Grille

Tracy from Centertown, MO
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

The light bulb in my freezer door burned out.

Remove the burned out bulb and install the new light bulb.

Parts Used:

Clear Light Bulb - 7Watt 130Volt

Peter from HAZELHURST, WI
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Freezer Light Shield Cracked at mid fastening point

replaced the broken one with the new part

Parts Used:

Freezer Light Shield

George V. from PITTSBURGH, PA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Ice maker stopped working

Remove the one screw holding the unit in place, unplug it, slide in the replacement, plug and screw it in.

Parts Used:

Ice Maker

Cary from ORLANDO, FL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

My ice container and Ice chute were freezing up and getting blocked, and my filtered water line was also freezing

I just followed the instructions on the video and it was exactly as they said......no surprises.

Parts Used:

Dispenser Door Assembly or Flapper

Joe from BRICK, NJ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Bulb burned out.

Screwed new bulb in socket

Parts Used:

Clear Light Bulb - 7Watt 130Volt

Jimmie from Surprise, AZ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Ice Maker Clogging up from frost build-up

Turn off power
Remove operator faceplate by pullling out on outer lower corners
Disconnect wire connectors from circuit board
Remove four screws from dispenser and pull out dispenser assy
Replcae Door ASsembly
Put everything back in place
Power up
Job Done

Parts Used:

Dispenser Door Assembly or Flapper

GARY from LIVONIA, MI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

the plastic slide cracked wouldn't support drawer

Super simple! Hardest part of the entire process was identifying which part I needed to order. Once I received the part (which shipped promptly and was at my front door within 2 days), all it took was 5 mins and a screwdriver and I was back to having a usable snack drawer!

Parts Used:

Pan Slide - Right Side

Cynthia from Hillsborough, NJ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

4 of 11 people found this instruction helpful.

Was this instruction helpful to you?

Ice Building Up In The Ice Dispenser Chute

Under the control panel there are three small holes. Insert ballpen or small flat screw driver on both outer holes to push a tab lock that holds the control panel in place. Then pull out control panel and three set of wires will be exposed and disconnect wire connectors (connectors have different sizes so you wont get confused in reconnecting). Unscrew four screws on each corner that holds the ice dispenser assembly (a part where you push your glass against to dispense ice or water. The flapper is exposed and easy to replace.

Parts Used:

Dispenser Door Assembly or Flapper

joselito from riverview, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

The shield light had burned the shield

I hung the new shield on the two inside pegs that were already there.

Parts Used:

Lower Light Cover

George from Cun City Center, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Ice maker was not making ice.

First i removed two screws that holds the ice maker in, unplug the plug to the ice maker. I was able to remove the old one. Place the new one in screwed in the two screws and pluged in the plug and in just a little while i had ice again. I am a women, if i can do it any one can. I had a repair man tell me it was going to be $250.00 dollars to replace it. I got on line ordered the ice maker and had it in 4 days. Very fast shipping and easy to install. Tina Kearns Beaumont, Calif

Parts Used:

Ice Maker

Tina from Beaumont, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

froze in freezer

unclipped and replace with new part.

Parts Used:

Dispenser Door Assembly or Flapper

Ken from Wesley Chapel, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Ice maker discharge was slow and jammed with ice and frost. The cause was a distorted flapper that did not seal properly, admitting warm air into the dispenser chamber.

Excellent video was available on the Parts Select website. It was simple. The selector panel pulled out by hand from the bottom. The subpanel was removed with the four screws. The flapper snapped out of the holder with two clips. The new one was inserted in reverse order.

Parts Used:

Dispenser Door Assembly or Flapper