All Installation Instructions for Kenmore Refrigerator 3639537823

Ice Crusher began to leave plastic in ice

We only needed the rear plastic cylindrical helix. After installing it, there was a squeal of metal on metal due to insufficient clearance between the rear moving blade and the Ice dispenser plate.

Refrigerator Ice Maker 7/16” (or ½” hole, stainless steel) washer just behind #334 Rear Moving dispenser Blade PS292310 to give clearance so it doesn’t hit #345 / PS292441 Ice Dispenser Plate.

This was my first time at doing this so it took longer than someone experienced. But, it worked!

Parts Used:

Auger and Front Helix Kit

Richard from BONAIRE, GA
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thought flapper in ice dispenser was problem. - more serious, more costly - not a DIY! New fridge here we come!

Opened, discovered not flapper but more complicated

Parts Used:

Dispenser Door Assembly or Flapper

Gail from LEXINGTON, SC
Difficulty Level:
Very Difficult
Total Repair Time:
More than 2 hours

1 person found this instruction helpful.

Was this instruction helpful to you?

Ice maker stopped working

Remove the one screw holding the unit in place, unplug it, slide in the replacement, plug and screw it in.

Parts Used:

Ice Maker

Cary from ORLANDO, FL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

Ice Maker Leaking

Researched on internet/you tube; ordered part, and did the repair. Easy to do and saved the cost of a service call.

Parts Used:

Dispenser Door Assembly or Flapper

Carl from SAN MARCOS, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Plastic guide in rear of bucket broke it guides auger when dispensing ice

I simply removed 6 screws that held bucket to face and pit on new bucket and put it back in freezer works great

Parts Used:

Ice Dispenser Bucket

Robert from FIFE LAKE, MI
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Had a drip which filled up the tray and leaked on the floor from water dispenser

There are Great videos on YouTube!!! Turned off power,Removed trim ring, Pushed a philips head screwdriver in one of the holes underneath the electrical panel with the selector push buttons. This releases the electrical panel. There are Three wire sets with plugs. I removed the plugs and took the electrical panel out. Removed four Phillips head screws and pulled out the big paddle switch. This then exposes the flapper. Replaced flapper with new one and reassembled everything. When I had everything apart, I cleaned with window cleaner. It was pretty moldy from the water leaking. Turned power back on and tested everything to make sure I didn't mess anything up. Works great

Parts Used:

Dispenser Door Assembly or Flapper

Rudy from CITRUS SPGS, FL
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Small grate on my ice dispenser broke

through away the old grate. Then put the new grate in the depression All done.

Parts Used:

Dispenser Grille

Tracy from Centertown, MO
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

drum light burned out

removed the bulb from the package unscrewed the old bulb & screwed in the new bulb.

Parts Used:

Clear Light Bulb - 7Watt 130Volt

Stephanie from DENVER, CO
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

My ice container and Ice chute were freezing up and getting blocked, and my filtered water line was also freezing

I just followed the instructions on the video and it was exactly as they said......no surprises.

Parts Used:

Dispenser Door Assembly or Flapper

Joe from BRICK, NJ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

The light bulb in my freezer door burned out.

Remove the burned out bulb and install the new light bulb.

Parts Used:

Clear Light Bulb - 7Watt 130Volt

Peter from HAZELHURST, WI
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Freezer Light Shield Cracked at mid fastening point

replaced the broken one with the new part

Parts Used:

Freezer Light Shield

George V. from PITTSBURGH, PA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

The light inside the oven had burned out

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

Parts Used:

Light Bulb - 40W

Catherine from SEATTLE, WA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

3 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Bulb burned out.

Screwed new bulb in socket

Parts Used:

Clear Light Bulb - 7Watt 130Volt

Jimmie from Surprise, AZ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Ice Maker Clogging up from frost build-up

Turn off power
Remove operator faceplate by pullling out on outer lower corners
Disconnect wire connectors from circuit board
Remove four screws from dispenser and pull out dispenser assy
Replcae Door ASsembly
Put everything back in place
Power up
Job Done

Parts Used:

Dispenser Door Assembly or Flapper