3639354590 Kenmore Range - Instructions

Pulled out heating elements, removed old drip bowls, replaced with new drip bowls, re-connected heating elements. Done! Looks like a new stove!

It was real easy all I had to do was turn the breaker off,Undo two srews and disconnect the two wires. Then repeated the process to install

Remove the oven racks, remove the two retaining screws, unplugged the wires. Install wires on new bake element, insert element into opening, install & tighten retaining screws, replace oven rack's & there you have it.

First - really check that the part you order will fit. Our oven is 30 years old and the first part we ordered was not correct, but it came the very next day after we ordered it which is amazing. We were more careful about measuring for the second one and it came almost as quickly. It only took a few seconds to unscrew the old element and then reattach the wires to the new one and screw it back into the oven. Very simple. I highly recommend PartSelect.

I installed the chrome drip bowl and plugged in the burner to make sure that it worked. Voila!! everything is now perfect and i have a happy renter. thank you so much for your fast delivery.

With less than 24 hrs from ordering to delivery, I was making cookies. Installation was quick and painless.

Remove dthe two screws and removed the element. Put the new element in and replaced the terminals and screws. Partselected is the fastest shippers on the net.

1. Turned breaker to the oven to the off position.
2. Removed screws from back of oven-This was the most difficult part of the entire process!
3. Pull out element about 3", then tugged a little harder to expose the wiring.
4. Unhooked wiring from element.
All of this took about 15 minutes.
When new one arrived (less than 48 hours), I did the reverse of the above. This took about 6 minutes replace with new element. Thanks so much!

Piece of cake. Pulled range out, unplugged it, opened stove, unscrewed element from back of stove w/ socket wrench, pulled out 1/2 way, unplugged bad bake element from the 2 wires, plugged in new bake element in, reattached to back of oven, plugged in stove and it worked.

Remove two screws holding element. Pull element forward exposing connections. Pull connections apart. Replace with new element. replace screws. Done

Cut power to oven from breaker box. Remove two retaining screws using a nutdriver at rear of oven. Slowly pull Bake Element from rear of range exposing connector clips. Disconnect at clips from oven wiring. Connect new Baking Element to wiring connectors. Push new baking element into rear of oven. Reconnect baking element using original screws with nutdriver at rear of oven. Turn on power to oven from breaker box. Job complete in 10-15 mins.

Removed the two screws pulled out the old element and slid the new element in and put the screws back in. I used it that night to bake supper

First I removed the two screws holding the element to the back of the oven. When I pulled the element out I disconnected the two wires and removed the element. I found the serial / part number on the existing part and order from PartSelect. The element arrived two days sooner than expected!! Replacing the element was a bit more difficult in that I had to pull the stove away from the wall and remove the rear cover in order to pull the wires and element through the insulation in the back of the oven. Four screws held the rear cover, but once those were removed the element easily went into place and the repair was finished. Cleaning behind and under the stove took a few extra minutes but the entire repair only took about 30 minutes, plus the wait time for the part. Two tips, pliers were used to disconnect and reconnect the slip-on connectors. The connectors were pretty tight and reaching to the rear of the oven was difficult to get leverage to pull apart and reconnect. Also, the oven light caused considerable glare on my glasses so I taped the door button controlling the oven light and used a flashlight to see inside. Otherwise, a simple repair. PartSelect had the best price on the element and service and delivery were excellent!

Simply turned off the power (circuit box). Unscrewed the screws holding the element in place and detached the element from the wires. Replaced with the new element and replaced the screws. Turned the power back on. Easy as pie and saved lots of $$!

removed two screws, pulled element out (which broke at the sparking site) Took screw driver to push off where the element was connected. Put new one in, re-did screws. Turned on and off oven. This company was great to work with, smooth sailing. It was funny when we noticed the problem-Husband said $125.00 repair, I got on net and said no about $40. He is taking me out to dinner tonight.