3638500482 Kenmore Refrigerator - Instructions

Removed old Ice maker and replaced with new Ice maker.

TURN WATER OFF TO REFRIDGE. TURN OFF ELECTRICITY.

Remove old ice maker (AFTER REMOVING THE BIG ICE TRAY) by disengaging two philips head screws but don't totally unscrew them. You must then totaly unscrew the bottom screw below the top two screws. Unplug the 5 head connection. (electricity)

Use adapter for the electrcity, etc from the box, (five head connection) Use the old plastic hose to hit the new cup. TIGHTEN TOP SREWS. LEVEL BY EYE. Turn the system on. Prime with some fresh water.

PS make sure that the light is on (green) and you will be in ice city. Be careful not to disengage the elcectic head when replacing the big ice tray.

HAVE A COCKTAIL!

I removed the screws that held the unit in place, and also the screws that held a plate that covered where the unit plugs in. I unplugged the unit, and removed it. Put the new one in, reversing the steps. Turned the new unit on, and had ice in 45 minutes! Summer is coming, I need my ice maker! This is the second unit I have replaced on this refrigerator, the first one was not releasing the cubes. This second one was a different style than the first, but same install process.

If a 74 year old guy can install an ice-maker in a 20 + year old fridge in 20, or so, minutes it must have had good pictures and BIG PRINT. Working quite well at this time!

Ice hopper had no ice in it. But water in door worked and if I added ice to hopper, it would dispense in door. I added water to ice maker but no ice was made. Replaced ice maker and all it required was to unplug harness and remove two screws with nut driver. Easy!

There was what seemed to be a half chewed up washer under the refig. door. The door wasn't closing all the way. DING!! Something was wrong!!

I looked up your schematic for the refrig door and decided what piece might have broken. It was a good guess and the part showed up a few days later.

I wedged up the refrig door to take the tension off the lower bracket. Then, just took off the bracket and replaced the broken door closing cam.

Removed Ice Maker (2-Bolts)
Removed Ice Tray Screw Motor (to get to Ice Maker Plug- 4 small screws)
Installed new Ice Maker and reinstalled Ice Maker Screw Motor
Extreamly easy

I used a block of wood to hold up the door. Then unbolted the lower hinge from the fridge. That is when I found out that it was fine and it was the upper half of the hinge that was broken (worn).
So I unbolted the upper hinge (mounted on the bottom of door) It uses the same part. So I installed the part on the upper half of the hinge.

I wish somebody would have told me that you need 2 of these for each hinge. The bottom one was in good shape, lucky for me.

Remove screw at hinge cover, top of door.
Remove two screw/nuts at hinge and remove hinge while holding door in place.
Lift door off of lower hinge
remove two nut/screws at bottom of door and replace closing cam. Be sure the pivot pin hole in the cam is lined up with the hole in door.

Next drill out rivet holding cam to lower hinge on the refer. Install cam with a pan head screw and nut (to replace rivet). It will help if you remove the plastic grille cover at the bottom of the frige.

Set door back on the lower pin and shut so the the magnetic strip holds the door in place. Re-install the upper hinge loosely. Adjust the door for an even gap and tighten the screw/nuts. Re-install the cover.

A very easy fix.

I first removed all of the door contents. I then removed the door from its mountings by removing two screws at the bottom bracket. With the door lying on the floor I then removed the two screws holding the door cam assembly in place. I inserted the new door cam, then reversed the process replacing the four screws.

Replaced the old cams with new ones, door works perfect now.

First of all, It was Christmas and no extra money to pay a repairman.
i got on the computer and started looking for a parts breakdown for an older GE side by side.
I finally found it and located the part I thought we needed.
I looked at several parts dealers and yours had the best price.
anyway it arrived in just 2 days. My son helped me remove the door and we put the new part on and I just saved the cost of a service call.

Thank You

Door needed to be supported before hinge assembly was removed. After replacing broken cam doors aligned and doors closing properly.

Removed refrigerator door and replaced bottom door pivot with the included mating cam and the door closing cam on the bottom of the door.

I didn't know that there were two mating cams and only ordered the door closing cam which I read online was the problem. It was the number one part on the part select list. The number two part was a kit including the door closing cam and the pivot with mating cam attached. It would have been helpful if there had been some notes that said check condition of both cams before ordering the part. So I have a spare door closing cam and paid an extra $19 including $8 shipping which negated a return.

The repair is easy - getting the right parts the first time is the trick.

It was as easy as the instructions were clear (and they were). Remove 2 screws and two nuts, pop out the old ice maker, pop in the new, plug in and tighten screws/bolts. It worked. I'm happy.