36384 Kenmore Refrigerator - Instructions

Did the repair just as the instruction said, once I read it. The part I didn't read was that if the plug was under the ice maker, you had to take the wire out of the clip on the side. So, had to dismount ice maker, unclip wire, remount maker, plug it in. Still under 30 minutes. Thank you.

put block of wood under the door, removed old hinge and installed the new one. about 15 minutes

Installation could not have been easier!

replaced lights in refrigirator and freezer

turn breaker off first then use thin blade screwdriver and plastic pry bar to remove light socket and switch there was plenty of wire so work was easy to install at both ends

we took off the old one and replaced it.

I had to defrost freezer first becasue it was heavily iced up. Then I found that one of the heater elements was "open". I removed both of the old heater elements and installed the replacement parts.

Did not do the repair because the unit arrived damaged. The packaging was in good condition. The plastic around the plug in shattered, and some of the plastic was inside the motor. Very good, and fast on adjusting the order.

I replaced both lower hinges without removing the doors. First a couple of observations. The hinge kit consists of two parts; the lower part (bolted to the case) consists of an “L” bracket with a plastic cam, and the upper plastic cam (attached to the door). For some reason the upper cam is available as a separate part . If both cams are plastic both are worn out. Don’t bother ordering the individual cam. If one hinge is worn out the other probably isn’t far behind. Consider replacing both at the same time. Examine the door check. It is an inverted “T” shaped bracket bolted to the door that also holds the door cam. The crossbar of the T are metal tabs that check the door swing. Way too fragile IMO. On mine the refrigerator side was cracked and broke off when I removed it. Since the stops are the same right and left. I just swapped them when I replaced the hinges. Saved $22. Replacing the hinges without removing the doors. {Warning if this technique goes wrong you will be stuck with a loaded door you can’t open.} Remove the vent grill. Stack three 2x4’s along the bottom of both doors ( 26” is about right ). Shim the door(s) up to compensate for the cam wear. About 1/8”) Use a 5/16 socket to remove the hinge from the case. Pay attention to placement of the shims and spacers. Then remove the door cam and stop bracket. Install the new door cam. Leave the screws a little loose. Replace the lower hinge and tighten the screws. Do both sides. Then carefully remove the shims and 2x4’s. Finish tightening the door hinge screws. Check the door swing. I used this technique twice. One to replace the refrigerator side hinge, then again to replace the freezer side hinge and swap the door checks. There were no problems and I saved the hassle of unloading and removing the doors.

Empty freezer;
Remove shelves and ice trays;
Unscrew and remove the rear vertical panel;
Unscrew and remove fan housing;
Unscrew and remove fan from fan housing;
Fan blade slides off the motor shaft without tools.
Reverse order to reassemble with new fan motor.

I did have to use the wire extensions that were included as the replacement motor had the electric connections in a different location from the original motor.

Overall, this was an easy replacement.

Remove contents of door , Remove top hinge cover - phillips screwdriver , remove top hinge screws ( 2 ) - socket wrench , lift door off lower hinge pin , lay door on edge , remove cam retention screw ( 1 ) - socket wrench , remove broken cam , install new cam , apply vasaline to cam and hinge pins , repeat above steps in reverse . Door now self closes .

Turned off water to ref , removed bottom kick plate , got a towel and disconnected the water line plastic fitting and un screwed the (2) tube clamps un screwed the coupling and ((carefully )) slid out the tube from the compression ferrels ! ( Be careful and do not break or distort them + remember exactly the order they are removed ! Slid the protector spring shroud from the plastic tube , took ogg the top hinge cover then remover the top hinge . Carefully lifted the door off feering the plastic tube through the bottom hinge with my foot ! Got the door off removed the bottom hinge + put the new on on, then removed the door cam which was broken on the bottom of the door , lifted the door up and carefully fed the water line through the new bottom hinge . Attached the top hinge and reassembled the rest same as I had dissambled it . Turned on water ( checked for leaks ) ! All working 100% a-ok ! This company is the best ! Ordered the part at 1 pm and had the part at 2 pm the following day many thanks : )

First we removed the door. Then we had to hammer the old part off including the old rivot. We fould a screw that fit and put this piece on. We held the door in place and screwed the hinge on the main unit.

First I took everything out of the fresh food door, then I removed the top hinge cover using a philips head screwdriver, and a nutdriver for the two screws holding the upper hinge. Lifted the door off the bottom pin, and placed it on the floor. Then took off the bottom hinge and used the Dremel tool to grind off the rivet holding the broken door cam on the bottom hinge. Used a nut and bolt to hold the new cam in place, and put the lower hinge back on. Then replaced the other cam on the bottom of the door itself, using the nutdriver. (Be sure to buy two cams, and have the bolt and nut to replace the rivet). Reinstalled the bottom hinge, put the door on, replaced the top hinge, and presto! Works great! Thanks to the others on this site for their stories - really helped make it an easy and quick repair!

Had to defrost a bit and then was able to remove rear freezer panel by simply removing the 2 screws holding it in place.
Old motor easily removed from its mounting bracket. and replaced with the new. Had to use the two wires sent with the motor. I clipped off the male connectors and joined them with wire splicers to the black and red wires clipped from the old motor. Then reinstalled.
The replacement motor works great. I was afraid the old fan blade might not fit but it slid on perfectly.