All Installation Instructions for Kenmore Refrigerator 36370249000

Left Vegetable Drawer Slide Rail was broken thus making it impossible for the Crisper Drawers to function properly.

I removed the Glass Shelf on top of the Vegetable Drawer assembly, unfastened the front rail from the broken slide rail and removed the entire assembly. I cleaned the parts and then installed the new rail. I placed the drawers in the repaired assembly and placed in the refridgerator. It really went well. I didn't need the other parts order. I only had them just in case they were needed.

Parts Used:

Vegetable Drawer Slide Rail - Left Side

Drawer Slide Gasket

Philip from McCordsville, IN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

4 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Refrigerator Water Leak

Icemaker waterline leaking inside by the grommet where the water line comes in the refrigerator . First removed the water line from grommet . Then removed grommet by hand from the fridge. Last, reversed prodedure.

Parts Used:

Fill Tube Grommet

BRIGIDA from MIAMI, FL
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins

4 of 7 people found this instruction helpful.

Was this instruction helpful to you?

light wouldn't come out of socket

It just unpluged and the new one plugged in. Simple. The part was reasonable and arrived very quickly. It sure is nice to have a light in the frig again.

Parts Used:

Light Socket

Joyce from Tacoma, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

water not being drawn up into icemaker

unplugged the old valve and disconnected the water line, then reconnected water line on new valve and plugged it in. It was an easy process but unfortunately that did not fix the problem. It is the ice maker it self so I will be ordering a replacement ice maker.

Parts Used:

Refrigerator Outlet Valve Kit

timothy from aberdeen, MD
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Refridgerator stopped making ice

Removed the old water valve from back of refrigerator by using a screwdriver. Pulled water line off old valve that runs into the fridge and inserted it into the new part. I used a pair of pliers to take off water line that runs into the water valve from the house. Screwed the water line back onto the new valve. Took about 10 minutes.

Parts Used:

Refrigerator Outlet Valve Kit

Doug from COPE, CO
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

light kept blinking on and off never same way

turn breaker off first then use thin blade screwdriver and plastic pry bar to remove light socket and switch there was plenty of wire so work was easy to install at both ends

Parts Used:

LIGHT SWITCH

Light Socket

michael from CENTRALIA, IL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

ice maker was leaking

thats what I did is remove the teo screws and took the old single outlet valve out. And put the new one in and put the screws back in. First turned off the water and put the water back on after I was threw and no leaks.

Parts Used:

Refrigerator Outlet Valve Kit

Phyllis from Minneapolis, MN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

a fan blade broken causing it to make a loud noise

we took off the old one and replaced it.

Parts Used:

Evaporator Fan Blade Kit

Marnie from Denver, CO
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Not cooling and freezer freezing up

I removed the condenser cover removed old fan blade defrosted the condenser section installed new blade and reassembled

Parts Used:

Fan Blade with Clamp

kenneth from carmel, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

6 of 14 people found this instruction helpful.

Was this instruction helpful to you?

Plastic shelf bracket broke that secures it to the door.

Remove shelf, wash shelf components, remove bracket that snaps into place, replace with new bracket by snapping locked in place and you're done.

Parts Used:

Door Shelf Retainer Bar End Cap - Right Side

Nicholas from Rocky Point, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

freezer too cold and refrigerator not cold enough because fan not working

Had to defrost a bit and then was able to remove rear freezer panel by simply removing the 2 screws holding it in place.
Old motor easily removed from its mounting bracket. and replaced with the new. Had to use the two wires sent with the motor. I clipped off the male connectors and joined them with wire splicers to the black and red wires clipped from the old motor. Then reinstalled.
The replacement motor works great. I was afraid the old fan blade might not fit but it slid on perfectly.

Parts Used:

EVAPORATOR FAN MOTOR KIT

Ann from LAPORTE, PA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Original evaporator fan (31 years old) was making a lot of worn bearing noise

Empty freezer;
Remove shelves and ice trays;
Unscrew and remove the rear vertical panel;
Unscrew and remove fan housing;
Unscrew and remove fan from fan housing;
Fan blade slides off the motor shaft without tools.
Reverse order to reassemble with new fan motor.

I did have to use the wire extensions that were included as the replacement motor had the electric connections in a different location from the original motor.

Overall, this was an easy replacement.

Parts Used:

EVAPORATOR FAN MOTOR KIT

T from SOUTHBURY, CT
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

freezer stoped freezing

my freezer quit freezing, it would freeze for one day, thaw the next, so I went online, found PARTS SELECT, LOOKED UP MY MODEL #, come to find out it needed three parts to keep my freezer to freeze, first part was a thermistor a small PART took me longer to remove all the covers, and shelving, PULLED THE OLD OUT, CUT THE WIERS TO SIZE, AND REINSTALLED, IT WELL! THAT WASN'T ENOUGH THE FREEZER STILL DIDN'T FREEZE IT THOUT IT WAS A COOL WORMING OVEN, HAD TO INSTALL THE THERMISTOR I, SO I DID, TEN MIN, NOW I THOUGHT THAT WAS IT BECAUSE IT STAYED FROZEN FOR A WEAK, HAVE YOU EVER EATEN SOUPY ICE CREAM? SO BACK TO PARTS SELECT, THIS TIME I BOUGHT ONE MORE PT, THE RUN CAPACITOR, FIVE MIN, THAT/S ALL IT TOOK TO INSTALL. I DID NOT KNOW AT THE TIME YOU NEED THE THREE OF THEM TO RUN THE FREEZER ONE TO KEEP THE TEMP., ONE TO KEEP THE FAN RUNNING THE WAY IT SHOULD, AND THE THIRD TO MAKE SURE THE OTHER TWO KEEP RUNNING. NOW I CAN SET IT AT 4- 5 AND. FREEZE.

Parts Used: