36369662990 Kenmore Refrigerator - Instructions

Pulled the door off easily and noticed that the spacer on the Center hinge was ground down to nothing and that a small screw in the bottom plate of the door was half way out. This screw would catch on the cabinet Center hinge bracket and stopped the door from closing. Problem was solved by tightening the screw and putting in a new "spacer" that kept the small screws from contacting the Center hinge bracket. The freezer door now closes like new.

I followed the directions of Steve on the installation video. He makes it easy to do the repair with his step by step description of the installation. I have repaired three different aging appliances with help of Steve and PartSelect's very helpful Customer Service.
I wish Steve a wonderful retirement and hope PartSelect can find someone as easy to follow for future videos. The videos are priceless for the repairs.

I haven’t received the wheel yet. Originally ordered on Dec. 13. Hadn’t received it by Dec. 20. Finally shipped on Dec. 22. Tracking said it was expected to be delivered on Jan.2. Not delivered. Then it said it was still on its way but it was unknown when it would be delivered. Still waiting on Jan. 6. By far the most expensive economy shipping ever, as this refrigerator is in a rental that can’t be rented until a wheel is installed.

The old switch was hard to remove. Thinking that I may have to loosen the wires I used a socket wrench to remove a clamp. This was unnecessary. In the end the switch did come out using a large size screwdriver. The problem was that the expanding plastic tongue is not visible from the ouside so you have to try to feel your way around. If i had ordered the replacement before and not afterwards I would have seen this before hand.

You will need a 1/4" nut driver or socket & extension.
Remove the back panel of the freezer compartment.
Pull of the wires, remove the fan assembly and replace the fan motor.

After replacing the light bulb and still no light I manually pushed the light switch button. Intermittently the light would come on then go out. I removed the power plug from the power source then replaced the light switch. I plugged the refrigerator back in and now I open the door the light comes on and stays on until the door is closed.

I ordered two switches, replaced both with a knife in 10 minutes. Interior light works, thanks.

Freezer worked great but no cooling to refrigerator section. Replaced with part ordered. Phillips head screw driver is all that is needed. Very easy to replace, it's plug and play. New part powered up neither the freezer nor the refrigerator. Went back to old part and atleast freezer still works. New part was no good from factory. The replacement part# matched the original. I attempted to contact PartsSelect but there was no response back.

Removed the door by removing the two screws holding it on. Do not try to do this repair with the door attached. Easily removed the old gasket. Getting the new one on the door was EXTREMELY difficult. I couldn't do it. After 90 minutes, I gave up and called my appliance repairman. When he arrived, he and I worked together to get the new gasket on the door. It took 2 sets of hands to do this. It still took us about 40 minutes. My repairman had a few choice words about the design of the system holding the gasket on the door. Ditto for me. So the cost of my repair was doubled because I had to pay the repairman to help me attach the new gasket. I should have just bought a new fridge.

I found instructions on the web about how to do this repair, so I ordered the part with confidence. But the instructions simply said "pull out the old switchlight". That was actually somewhat difficult as the clip on the side intended to hold the part in was stubborn. I eventually used a utility to slice off the clip. From that point, it was just a matter of plugging in the new switchlight , which was very simple.

Cleaned oh t freezer removed floor. Removed back inside wall removed and replaced fan and put back removed parts


L

first i removed all the screws inside the freezer compartment took out theback and bottom to get to the evap motor,unpluged the wires and removed the evap motor ,removed the fan from old unit and put it on the new unit them mounted it to the back wall of the fridge,,, and put back top and bottom

we took off the old one and replaced it.

After watching video I took off end shelf caps. It took close to 10 mins to replace them.

turn breaker off first then use thin blade screwdriver and plastic pry bar to remove light socket and switch there was plenty of wire so work was easy to install at both ends