36369 Refrigerator - Instructions

All repairs made in freezer compartment.

MAKE SURE YOU UNPLUG THE REFRIGERATOR BEFORE WORKING ON EQUIPMENT

Removed ice tray.
Removed bottom cover, 2 screws.
Removed center cover, 2 screws.
Removed backside cover, 4 screws.
Removed fan assembly from back wall, 2 screws.
Disconnected wires from defective motor, old fan blade was cracked spinning freely on shaft.

Reversed the order for re-assembly.
Plugged in refrigerator, now working great.

Make sure you buy the rubber grommets that supports the motor, I did not and did not notice the old ones were worn out. A vibration is coming from the new motor after repair because I used the old grommets. These should be included with the new motor.

Would have been an easy job but the bottom channel of the refrigerator door that the gasket snaps into was rusty and had to be cleaned out with a screw driver. Took some working with it to figure out why it wasn't snapping in hence the long time to fix it.

The freezer door gasket went much better. It had been folded for shipping and had to be heated per the instruction to ensure a seal. That was easier than I expected it to be.

The seal seems fine now. No moisture. I wish I had done this sooner!

just unscrewed the 3 screws, attached the rounded plug that came with the unit and screwed back only 2 screws. ice magic in about a couple of hours

While the switch did last for 9 years, the design is poor due to the failure mode. The failure should be to fail off or not able to turn on the lights which would be inconvenient but would not warm the refrigerator contents. Arcing at the contacts eventually caused the switch to "weld" closed. It is not obvious that this is occurring so it took some time to recognize why the temp inside the ref was high while the freezer was OK. Replacing the switch was easy once it was recognized as the problem. All that was required to replace the switch was to remove the screws holding a fiber cover and then pulling off the aluminum cap which covered the switches. Unplug the switch an squeeze the keeper on the switch to release it and pull down. Pop the replacement switch in place and plug the wires harness back in. All in all it took much less time to replace than it has to write this up. T Pope

first i removed old gasket then pressed in new one very easy repair

My husband did the repair, and even though our refrigerator is roughly 20+ years old, he was able to adapt it to work in all the right spots and we now have ice cubes! I'm very happy we did not have to spend $2000 on a comparable refrigerator.

First I replaced the double valve because the ice maker was not filling with water. It still did not work. Then I replaced the ice maker itself. This worked and was relatively easy to replace. I had to use the water fill "slide" from the old ice maker. The new one was too narrow and it leaked water into the freezer.

The existing light switch was very hard to remove. I ended up having to grab it with a pair of pliers and pull it out. Once it was out, it was very easy to put in the replacement and it seems to be working fine.

Remove back cover, exposing fan motor. Turn off power, remove nut on fan blades. Remove fan carefully, do not bend. Unhook wiring harness. Remove three screws that hold the motor on the back frame. Remove old motor, install new. Carefully, reinstall fan blades, hook up wiring, and your ready for tryout. Also do some cleaning while your there. Clean old fan blades with hot soapy water or contact cleaner. Everything runs better clean!

Removed screws (4 total) that hold everything together. Removed broken pieces; slipped two new side pieces in place, replaced the screws; put entire frame into place, glass shelf on top, drawers in place: Done!!

First unplugged frig. Took off cover to fan, then bottom & back panels in freezer. Unplugged the fan to the wires & marked them so we would know how they went back. Unscrewed the frame that holds the fan, laid the old one next to the new one so we could tell how it went. Only took a few minutes to do this, then put it back in the same way we took it out. Plugged frig. back in & it took off. Very happy with this. Runs like a new one.

After I bought what I thought I needed for the repair. I asked a friend to come over and look at it. He changed the
the light socket and put the same light bulb in and it works great. I am returning the light switch but decided to keep the light bulb.

Getting on the internet was so easy. This was really very simple. Thank you for making what I thought would be a big ordeal into something very simple.

Paulette Johnson

Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.

remove lower back cover - disconnect wires to fan motor - place 6" fan to blow on condenser - fridge began cooling & freezing again - ordered part - part arrived - removed fan motor & bracket - cleaned brackets & fan blade - cleaned lint & dust from condenser compartment (took longer to clean than anything else) - replaced fan motor - replaced cover - was hero with wife ... :-)

Turned off power, removed cover from Ice maker, checked resistance across thermostat for zero (read open), all other switches read proper value (when activated). Ordered and received thermostat. Removed Ice Maker from freezer, removed two screws holding ice tray to Control Assembly. Removed Thermostat and replaced with new one. Applied Silicone Sealant to face of Thermostat for adhesion to ice tray when assembled. Remounted Ice Tray to Control Assembly and remounted in freezer. Works Great...