Models > 36368677895 > Instructions

36368677895 Kenmore Refrigerator - Instructions

All Instructions for the 36368677895
91 - 102 of 102
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Foam Air Duct damaged by defrosted meat
Removed ice cube tray and fan cover using a cross-tip screwdriver. Old air duct foam had been damaged by defrosting meat and made entire refrigerator smell. Part easily slides out and slid in knew foam. Replaced with new air duct foam after thoroughly cleaning refrigerator by sliding it into place, replacing fan cover and ice cube tray. Hardest part of entire replacement was cleaning refrigerator. The actual replacement of the part took less than 15 minutes.
Parts Used:
Air Duct Foam
  • Benjamin from Virginia Beach, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
light would not stay on
First I flipped breaker to off position for refigerator, Pulled down on socket and broke it free. Then took needle nose piars to pull wire and plug out from hole, so I could conect to new light socket then snaped it in place . Hardest part was getting wire and plug out of hole.
Parts Used:
Light Socket
  • Kenneth from Leavenworth, KS
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Reistall shelf
Replaced cap and reinstalled. But I used iron nail inside cover to hold right side because crack was at right hole and right part would not help.
Parts Used:
Door Shelf End Cap - Left Side
  • Oleg from Lees Summit, MO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
needed new light socket
Pulled out old socket.pushed in new one.
Parts Used:
Light Socket
  • Charles from Williamsburg, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
broken crisper drawer support
quick and simple--removed the old one and slid new part in on same support pins.I had the new part via UPS LESS THAN 24 HRS.FROM THE TIME I PLACED THE ORDER! THANKS, SOMEONE IS REALLY ON THE BALL.
Parts Used:
Vegetable Pan Cover - Glass included
  • Richard from Owls Head, ME
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
failed light switch
I started removing the switch by prying on the right side with a screwdriver, when it emerged enough I used pliers to finish removing it. I then unpluged rhe wires from the bad switch and pluged them on the new switch and "poped" it into the hole.
Parts Used:
LIGHT SWITCH
  • Jules from Crowley, LA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
lost screw and insert plug
replaced the screw and covered it with the plug. The pleasant surprise was that the requisite screw plug were available, especially after over 10 years.
Parts Used:
Screw Plug Button Insert - Almond
  • BENNIE from KNOXVILLE, TN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
no light in freezer
Connected the 2 wires and pushed in the switch until it clicked.
Parts Used:
LIGHT SWITCH
  • christopher from collegeville, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
The fridge was making a strange bird like whistle
The repair went smoothly and surpising easy! Get access to the back of the fridge. Unplug fridge, remove cardboard but save to put back in same place. For our fridge it was to bolts removed by socket set, removed old condenser fan motor (applyed a little pressure) and placed the new condenser fan motor in. It's easier with two sets of hands, but I've got to say DIRECTIONS OTHER THEN CUSTOMERS TESTIMONY SHOULD BE SENT WITH THE PART!! Otherwise quite simple.
Parts Used:
Condenser Fan Motor
  • LaNita from Petrolia, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Socket set
Was this instruction helpful to you?
Thank you for voting!
refig light did not work
per your instructions
Parts Used:
LIGHT SWITCH
  • paul from east hanover, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
The bottom part of fidge was warm with water droplets on the its ceiling.
Removed Ice shelf,
Remove rectangle cover by removing the two screws and lifting straight up.
Pulled fan off slowly.
Removed two hex screws holding motor bracket.
Remove cover.
Remove two hex screws holding remaining bracket from fridge.
Pull wire off motor noting where they were plugged in.
Pull apart brackets holding motor and remove motor noting how the motor and brackets fit together.
Reverse to install.
Parts Used:
Evaporator Motor Kit
  • Charles R from Renton, WA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Noisy fan
Emptied freezes, turned off power, took floor of freezer out [4 screws ], took two screws out of fan mounts and replaces fan. Reassembled by reverse process. Simple
Parts Used:
Evaporator Fan Blade Kit
  • Robert L. from Eldred, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 36368677895
91 - 102 of 102