36361542211 Kenmore Washer Dryer Combo - Instructions

open door, remove two screws from below the top. gently remove the top from the side and bottom panels. remove two 5/16 screws from front panel hold panel so it does not fall. the bearing assembly will come out by moving the bearing towards the dryer, and pulling upwards. replace with new bearing, use 4 front dryer slides and reinstall the top and front panel. can be done in less than 15 minutes

This took less than 10 minutes to complete. 1) pull off the top of the dryer and remove the two screws that attach the front panel to the side panels. Once you pull the front panel towards you, away from the side panels, you can remove the front bearing. Be sure to be careful not to pull apart the wiring on the left side of the front panel. If you do, it is easy re-attached by hand. The front roller bearing of he drum can be removed by hand. Simply pull upward, with a steady pressure, on the bearing. It will snap out with this gradual pressure. The slide can be inserted by hand, with the two gray slide at 11 and 1 o'clock and the wite slide at 10 and 2 o'clock. The new bearing will snap into place by hand. Carefully insert the light bulb into the hole in the top of the new bearing whle snapping into place. The web site provides a good diagram that illustrates the various pieces and assembly. Once the bearing is in place, lift the dryer drum and set on top of the bearing as you re-attach the front panel to the side panels with the screws removed earlier. Replace the top by snapping back into place. Less than 10 minutes.

By watching your video which was very helpful as I never made this repair before. All worked out fine. Since then I have ordered other parts., (drum bearing kit, door slides and a new belt.) The video on replacing the drum kit is very helpful too. One other fact is prices beat all other sites I looked and when I'm done the dryer will be "rebuilt" I recommend your parts to everyone., they are great quality.

Removed 2 screws to remove top. Removed 2 other screws to remove front. Removed old parts. Installed new parts. Reassemble all afetr cleaning duct work out.

The dryer was very noisy when it would start. The drum had warn the pads out and the drum was riding on the drum bearing. It really isn't a bearing more of a big piece of plastic. On the bearing are 4 slides (2 white and 2 green). These are easy to replace if the bearing is good. I let mine go too long and wore part of the bearing off. To fix: UNPLUG! Open the door and find 2 screws facing upward screwed into the top. Remove these 2 screws and remove the top. Take notice of how it comes out of the dash. On each side of the front panel (from inside) there is a smaller screw with a bigger head, remove both of these. You can now lift the front panel away from the drum and pull the front panel right out. It would be a good time to take a shop vac and clean all the lint out of this. Mine was almost full. If you are changing the bearing it is held in place with clips built on the bearing. Remove and replace. Put on the new slides as well. There is a little tab on the bearing and a hole in the slide. put the hole over the tab. The green ones I put on the top and the whites on the outter sides. Put the bottom of the panel in first and line up the drum on the new bearing, replace the 2 big headed screws, line up the top in the dash and lower into position, replace the 2 screws up inside the door and you are done. I have no dryer experience and would rate this job on a scale of 1-10 to about a 3 or a 4. There were no real suprizes.

loosened two hose clamps and four screws to replace the anti siphon valve.

Dryer started making screeching noises while running, got progressively worse. Without taking it apart first, I ordered a front drum bearing and slides because this site said it fixed the problem the majority of the time. The site said replace the slides in pairs, but there are actually four. I picked up 2 more at a local appliance store, at roughly twice the price. Turned out I didn't need th replace the plastic piece called drum bearing, just the 4 slides that clip onto it. It is really easy to get the top and front off with just a phillips screwdriver. I did not check the rear center main bearing, as it requred removing the drum. The squealing lessended but it still was bad. Took it back apart and pulled the drum, and fount the rear main bearing bad. I found one at the same local store for only 2 bucks more than on this site. This was a bit more of a hassle, you really need two people to get it mounted to the drum. Tip-pre thread the holes with the self tapping screws, it makes it easier to get it together. There was a bit of lint build up under the drum heating element cover, so it was good to clean that out. Also blew all the dirt out of the motor with compressed air and shop vac. There was a access panel on back to get to the motor and belt tensioner. Got the dryer all buttoned up and now it runs nice and quiet.

removed top, 2ea screws ;removed front door,2 screws; removed left side panel,screws on bottom and back; removed belt,pulled out drum. replaced top drum bearing,installed green and white slides,re assembled w/ new belt,ops. check ok.

Un plug the dryer. Gather phillip, flat head and torix screw drivers. Remove the rear of the dryer to get the spec sheet with the appropriate part number. Next called for part. Belt installation requires removal of front and top of dryer in order to slide belt over the drum. Getting to all the fastners requires tilting the dryer on its back. Clean out excess lint from dryer interior and duct work. Slide drive belt over drum and use some masking tape to hold it in position. Reassemble dyer. Return dryer to upright position and put the belt on the pully and tensioner from rear access port. Remove tape. Replace access panel. Reattach vent duct work. Plug in. There are 5-6 different size screws holding everything together...you may want to use masking tape to label where each type of screw goes. All totaled it took about an hour and cost less that $25. Well worth the effort.

Replacing the front slides is easy. Just buy the parts and pop them in. The rear drum bearing is also easy, and you do not have to spend $50. Once I had the parts in hand, which is an axle from the rear of the drum and a bearing sleeve from the rear of the dryer cabinet, it looked quite simple and it is. I went to a hardward store, bought a bronze bearing that fit the axle and the sleeve and a C-clip. Cut the bearing to the correct length with a pipe cutter, and retain over the axle with the clip. Grease it up, and put the dryer back together. Total cost, $5. It works great.

Parts were easy to take out and replace with the new ones.

Well, the intall would have been great except for the fact that I needed another part. If your belt breaks there is a reason for it. Make sure you check all the parts that work with the belt. Their was a pully the was defective and also need to be replaces. I think it would be a good idea to put a little note on the page for the Belt Drive to let people know that if you are replaceing the belt you might want to check the Idler Pully for it too might need to be replaces. I'm not an expert and if that was on the page for the Belt Drive I might have look at the pully before I ordered and I would have ordered the part along with the Belt Drive. As it was had to wait another 4 day to get my dryer fixed. I'm very happy the Parts Select has all my parts and they pretty good at getting them out to me in a good amount of time when I need them.

Took off control panel,top,leftside facing door,and,door panel. Replace the 2 green and 2 white slides, the front drum bearing, the rear bearing and groundind strap behind the heating element,and new belt. Put back together,run's and sounds like new. The hardest part was putting drum bearing in inside and backside of drum by yourself. Replace belt with left side panel off. Easy to get on that way.

I was teaching my associate how to do this repair so I showed him how to take off the top of the dryer. Then I showed him how to replace the drum slides. I had him clean out the dryer since we had it apart, and I also showed him how to remove the drum and then reinstall it. This was a very easy repair, and he learned a lot that he otherwise would not have known. Thanks for getting the parts to me so quickly. Rob from Clarks Summit.

I removed the two screws inside the door and popped the top loose. I took the top off to see and have access to the interior. I leaned the front out and inserted the belt around the drum (with my wife's help), replaced the screws and laid the dryer on it's face on a rolled up blanket and proceeded to run the belt around the pulleys (two). The drive pulley was easy but the idler pulley, not so easy. I had to figure out how the pulley arm was supposed to provide tension on the belt. I figured it out by looking at the diagram. It was then I found the idler pulley was broken and fell apart in my hand. I advise that a new pulley be installed at the same time as the belt. Everything I read on your web site helped.