36361542211 Kenmore Washer Dryer Combo - Instructions

It was super easy, done in 5 less than 5 min. Thanks Parts Select. Parts Select made it easy to find the replacement part by posting pictures. Thanks

First unplug dryer to prevent electrical shock. To remove the front of the dryer, open the door in top left and top right corners is a machine screw. They can be removed with a Phillips screw driver. Lift the top slightly and let front fall forward about 6 inches, lift slightly. Two wire will be connected to the switch in the door. remove the wires and squeeze the tabs on both sides of the switch and push it out. Push new switch in to replace old switch and reassemble.

I went to You tube sight to see how I can remove front of washer so I could inspect inside and see if the problem was visible. A butter knife easily released the tabs that hold the front of washer on. My wife in the mean time found a you tube video that showed the same problem and I ordered the part right away. It showed just two screws and a plug that had to be removed. I always buy my parts from part-select because the quality and speedy delivery and tracking is great! This was an easy fix!

I first unplugged the unit, opened the top, disconnected and took off the control panel, took off the front panel to determine the source of the squeaking noise coming from the Dryer. I saw that 3 of the 4 Front Drum Glides were gone and the drum had worn away significant amounts of plastic from the Top Bearing Assembly. I purchased the Top Bearing Assembly and a set of 4 Front Drum Glides. Disassembled the damaged parts and reassembled with the new replacement parts. The reassembly took less than 20 minutes. I plugged in the Dryer and viola! It works as good as new.

Purchased spanner wrench for tub nut wouldn’t budge, impacted off. Then spin tub took 2days to get loose, lots of WD40 , also heated up center area, used a small sledgehammer head to hit a socket on the large part of the shaft . Had to take out outer tub to replace seal and support bearing unit.

This kept the interlock open and shut off the dryer when the door swung open The broken latch was popped out using a flat blade screwdriver and the replacement snapped into place by hand. Good as new!

If you're handy with a right angle grinder and a cutoff wheel, it can be done.

Order the washer hub, hub nut, and the spring washer above the hub nut.

Get the agitator out. a pair of flat bars and some hammering on the agitator retaining bolt helps a lot. Loosen the retaining nut a few turns, pry and hammer at the same time, repeat until he agitator comes out.

On the bottom of the tub assembly is a brown plastic bracket that holds the spin solenoid. Remove it before you dismount the tub assembly. It's easy to break, and it costs $65.

Dismount the tub assembly from the cabinet. Turn it over and remove the motor. Unbolt everything that can be unbolted. Cut away enough of the large metal plate that was bolted to the bottom of the tub so that the tub assembly will stand upright on a five gallon bucket.

Stand the tub assembly upright on the five gallon bucket. Cut away the hub nut. Try not to cut into the black steel disk on the bottom of the tub. Soak the metal parts with PB Blaster, Kroil, or similar. Slip a three foot long piece of 1 1/4 pipe or conduit over the stem that held the agitator. Hold the pipe upright. Drop a four foot long steel rod into the pipe. Use the steel rod as a slide hammer and whale away. Stop frequently to spray your penetrant, and keep hammering. Eventually you'll drive the old washer hub out of the drum. Remember, everything is plastic and not indestructible..

Before reassembly turn the tub over and clean up the mating surfaces, ditto the agitator. When reassembling use antisieze compound on the mating surfaces.

Pulled the unit all apart to replace the rear drum bearing. Also replaced the front bearing. Works like brand new. Easier then I thought

First, I removed the 2 screws for the top panel, lifted the top panel off, then I removed the 2 screws holding the front panel, tilted it forward to clear the drum, disconnected the door switch and set the panel aside. I then installed the 4 slides on the new front bearing, removed the light socket from the old bearing, removed and discarded the old bearing. I installed the light socket into the new bearing and the bearing assembly snapped into place on the front panel. I then re-connected the door switch, aligned the front panel with the drum, secured the front panel with 2 screws, then carefully placed the top panel back in place and secured it with 2 screws. I checked the rotation of the drum and it worked like a champ. Matter of fact, that same day I put this dryer and a matching washer up for sale at 8:30 am on October 31st and by 9:20 am I already sold them!! I delivered and hooked them up and the dryer works great!!!

I removed the washer front cover and slanted cover between washer and drier to see where the noise was coming from. I found 2 rubber stabilizing straps broken away from the tub cap and popped off the snap on tub cap to see if I could repair it. I could not, so, I ordered a new tub drip cap thinking that would solve the problem. Well, the new cap was not identical to the one I took out. The pegs that the straps are supposed to connect to were nonexistent ... frustrating. After reading several help files, I discovered that GE had changed the design of the drip cap intentionally and had done away with the stabilizing straps. There was no mention of the design change in the instructions that came with the new part. Okay, now the real fun began...LOL. Removing those darned tub hangers was a challenge because I was working alone and in a very confined area. The instructions said to remove the 2 front hangers and let the tub sit on the floor. I did not like doing that for fear of damaging other parts under the tub. Additionally, I could not reach the rear hangers if I did it the recommended way. So, I used some oak boards and straps to lift (jack up) the tub as high as possible and to remove the weight off of the tub hangers. With the weight removed from the hangers, they snapped out of place...not easily. The 2 rear hangers are hard to reach and the plastic hanger caps were difficult to unsnap. I had to slam the plastic caps against the frame to get them unsnapped from the metal rods. The instructions did not contain any description of how the hangers are connected or how to get them removed. Anyway, I put it all back together and tested it. Everything is working fine now...minus the stabilizing straps. It would be very easy to injure yourself doing this job. Take your time and consider the consequences before jumping into this alone or with improper lifting equipment or mechanical skills. It was tedious and frustrating but not impossible. Good luck!

I had already replaced the four (4) small wear strips which were like short strips of teflon, and the squeaking decreased almost completly. I noticed that front side of the drum itself had started to wear through the actual plastc drum bearing, but I hoped having previously replaced these tefon strips that would be the overall fix.
Wrong again... after a few weeks the squeeking continued until I ordered the new drum bearing and replaced the worn one with the new one. I was able to re-use the previous teflon wer strips, and it's like new now at least the squeaks are gone,

The actual fix was a very simple remove old drum bearing, snap in new drum bearing install old teflon wear strips put four screws in top, and front panel and I was back in business

Originally I thought that the Start switch was the issue, and ordered one. After taking the machine apart and running some tests, the issue was clearly not this switch, but a different switch that cuts power when the belt tension is no longer being applied to the idler pulley spring. I fixed this by bypassing this switch, which in my opinion, is error prone and serves no purpose. The switch can be accessed by removing the control panel, then top cover, then front cover, then drum. The bogus switch is screwed to the bottom left, near the motor. The idler pulley spring rests against it. Just disconnect the switch wires, then clip, strip and crimp then together to bypass the switch, and voila! Now if the belt breaks or comes off the pulley, the motor will continue to run, but you wont hear the wet clothes flopping around, so that will be the indication that you have a belt problem. Hope that helps!

Opened dryer door and removed two screws that held front of top panel on. Lifted top panel off and removed two screws that held front panel to side panels. Tipped front panel forward and replaced all four slides. Cleaned everything off and put back together. Works great again. Thanks for this site and for others that have done these repairs before and posted their stories.

Pull the two scews to release the top of the cabinet. Pull the two screws to release the face of the cabinet and tilt out.
Take the old slide out and install the new ones.
Put it back together.
No more squeeks
My wife thinks I'm a genius...

I followed the very easy YouTube video and got the three tools I needed before beginning. I started with removing the parts of the dryer and that was extremely simple by following the steps in the video. Took the door off last, located the parts that need replaced that didn't require any tools at all. Then put all the parts of the dryer back on in the order I removed them. The entire process was about 25 minutes but I would say I spent more time really cleaning the dryer and lint build up than actually doing the repair. Video was super thorough and easy to follow, I've never attempted any kind of repair of an appliance and I'm extremely happy that I had the video and the parts that were recommended to fix my problem, were spot on. Saved me hundreds of dollars and time. Thank you so much!