36358475890 Kenmore Refrigerator - Instructions

I removed the ice tub. Removed the screw on the left side that holds closed the section where the icemaker plug is connected. Disconnected the plug. Then removed the bottom right screw. I was then able to remove the Icemaker by unhooking it from the bcak freeze wall. I disconnected the icemaker from the fan gaurd. Removed the icemaker cover. unscrewed the 3 icemaker screws and opened up the chamber. removed the old Ejector Blade Drive Cam by removing the outer srew that hold the gear to the icemaker. changed the cam with the new one and reassembled everything.

Used the nutdriver to loosen two screws, life out ice maker, disconnect electric plug and put aside. Placed the new icemaker on the loosened screws, plugged in electric connector and tightened screws. Used small level to verify that unit was level.Waited about two hours for first cubes to be released into tray - has been working fine since!

I removed the lower screw (not needed for the new icemaker), loosened the 2 top screws, unplugged the wire harness and removed the old icemaker. Unpacked the new icemaker assembly from the box, wiped the ice cube depressions to remove any debris, snapped on the water tube adapter, hung the new assembly on the 2 loosened upper screws and tightened the screws. The wire harness required the supplied pigtail plug which made the wire assembly long and awkward to replace the ice bucket/dispenser assembly, plugged it in and was done. It took a total of about 10 minutes for the entire operation and had a full bin of ice cubes within 36 hours and was ready for the ice dispenser/crusher in the freezer door. Easy install!

1. Unplug the fridge
2. Removed the outer facing of the dispenser outside the freezer door. This is fairly easy, better with a tool (plastic scraper) that won't mar the finish.
3. Removed the plastic plate with labels -- water, ice, etc. This is done by sliding a small jewelers screwdriver into the slots on the left, middle and right in back of the plate. These are difficult to see without a flashlight.
4. Removed the four screws in the panel behind this plate.
5. Unpluged the large cable on the left side after the panel is freed.
5. Removed the rubber "dispenser" button. this just pulls off.
6. Remove the panel
7. Lift flapper up and remove. Clips hold this in.
8. Put new flapper in place.
9. Use reverse order to put back together.
Piece of cake. Ice maker no longer frosts up.!!!!

The parts were here the next day. After removing the old ice maker it was a simple installation using the adapter cord furnished. It took about 15 minutes. You have to work with the cord some to get it to fit behind the ice maker, but it does fit. The ice maker started up immediately & works great.

It was as easy as the instructions were clear (and they were). Remove 2 screws and two nuts, pop out the old ice maker, pop in the new, plug in and tighten screws/bolts. It worked. I'm happy.

The video on the site was very helpful. The repair was really easy. It was exactly the way the video showed how to do it. I would definitely use this site again to find parts, figure out the "how-to", and use for skematics of appliances. Thanks.

turn off water. turn off electricity. empty freezer section of frozen food. remove ice bucket. loosen two screws holding IM to wall of refrigerator. lift off icemaker, and then unplug it as you remove it. INSTALL new IM by: putting new water funnel onto new IM. attaching adapter cord to IM. plug in IM electrical cord to refrigerator and then hang the new IM onto the two loosened screws on the refrig wall. Now tighten the two screws. the extra adapter electrical cord hangs below the new IM, but does not get in the way when you reinstall old ice bucket. reload food, turn on elec and water. PS. i had a crack in the casing of the new IM, so i got a new one, but that one was cracked too. so i just installed the second cracked one. hope it is not a problem.

REplaced old icemaker with a new one. Install simple, However that was not the problem. I then replaced the water valve. Still no ice. I check the electric connection was OK. THe problem was the elbow fitting on the top back of the refrigerater leading to the icemaker was blocked with ice.Cleared it and turned water faucet up all the way. Ice maker worked.

The instruction video was great, mine was easy than even the video showed it to be. I changed it out in less than 15 minutes and it works great. The niocve things I didn't have to wait for a repairman or my husband to fix the problem.

Watched video on website then removed old ice maker. New one went in without any problems. Working great. I am a 60 year old woman and had never done anything like this but so easy. Husband scared now, doesn't know what project I will take on next.

remove the 'pop-out " frame around the door recess, you pry the flexable seal from around the ice despenser, have someone hold the unit with the wiring, remove the one screw that holds the door recess, and replace the new one. reverse the procedure. remember to unplug thr frig. first

install icemaker water was allways delivered to previous unit water is not being delivered to icemaker still having difficulty

really simple,take 2 nuts loose pull the hose out and then replace.took less than 30 minutes

After what I thought was a thorough troubleshooting of said problem I replaced the Water Valve Assy which was really easy as the video shared, but it did not fix my problem. I had forgotten to pull the water line apart at the coupling below the doors (this was a troubleshooting step in another area). The water not dispensing was due to the line being frozen! Putting all items in a cooler with a couple blocks of ice and leaving the freezer door open for the length of watching a movie, the water was flowing again. Still no ice though. Ice maker vs mother board at the rear of the fridge, Hmmmm. Went with the ice maker, watched video, ole Steve makes the plugs disconnecting look easy, I had to use a flat head screwdriver to open the clips (he doesn't mention that) and I had 4 screws where he had 3. Also he didn't mention about the instructions which gives you 3 options with your unit. I had to re-use my Plastic Stripper Plate along with the Fill Cup and Ice Maker Insert. After completion of installation and about a half hour later, I heard ice fall, Wooohoooo!!! Overall the experience will make me think to utilize PartSelect again when needed. Reasonable prices and decent shipping time. Now the freezer light is out...