363151 Kenmore Dishwasher - Instructions

Replaced all ordered parts.

First I looked for blockage and found none.I took the pump off and hooked power to it in my work shop and it did spin when powered up.We had broken a glass in the washer and thats when the problem started. I did find a few small pieces in the check valve assembly. It did not look bad but for cheap I ordered the part. Ran the washer and it drained on the wash but not on the final. Turned off the power.Slid the wash out where I could get to the power and not unhook the water. Turning off the power I disconnected the wires and carefully turned the power on and touched them to the pump and forced it to drain knowing that the pump worked I thought it would at least empty the water. I touched the wires to the pump and the board clicked the water drained. Hooked it back up. Ran it and has been working great since.

The leak was coming from the drain valve shaft and I found the tips to replace the seal from this website. I was able to reach everything without removing the dishwasher from the cabinet. Once I got the cam lifter off the old push on nut was corroded so it was easy to get off. The old seal was recessed so I used the point of an ice pick to gently pry it out. The new seal was easy to push in place but the push on nut was a bear. I saw other comments about using a deep socket to push it on but I didn't have one the right size. I was able to hold the end of the shaft with pliers and pushed the nut in place using a screwdriver. Ran a short cycle and no more leak. Thank goodness for this website. Found the part easily and the other written comments were very helpful.

I watched the video and did exactly what he did. I am a novice when it comes to repairs. I learn as I go. This repair went flawlessly. Ordering was quick and easy. The part arrived quickly. The repair took less time than expected. The part was what I needed and nothing else broke or went wrong when repairing the original problem. It was a 100% success.

removed old drawer-like basket, installed the new duplicate replacement part. Easiest "repair" I've ever done!

Removed 4 screws, took off basket covering, put new part in one turn, then replaced covering. Plumber had come out, I watched what he did, he had to order part and come back. I asked how much he didn't know but said cheaper than buying a new dishwasher. When he left I started calling around about the little plastic part that I needed. Part was $15.50. They called and said it would be $110.00. Needless to say I called them out and ordered the part myself and put it in. Took me like 6 minutes and cost $21.69. I was so mad about this situation that I even got my service call money back that I had already paid.

I simply removed the front toe kick panels.
The solonoid is staring you in the face.
I removed the small nuts on back side of the solonoid bracket and removed the retaining clip and springs.
I installed the new solonoid and was very surprised how easy it was.

I DID turn the power OFF at the breaker panel prior to starting the repair.

First I removed the four screws that secure the dishwasher to the underside of the countertop. Then I removed the four screws from the front cover at the toespace. Next I used an adjustable wrench to turn the feet to lower the unit enough to slide it out of the compartment. I unplugged the dishwasher and turned it on its side in order to access the hose chamber. I used a pliers to loosen the clamps at each end of the hose chamber and removed the the damaged item. Next I slid the ends of the new part into place and used the pliers to reposition the clamps. Finally I returned the dishwasher to an upright position, slid it back into the compartment, adjusted the feet to raise it to the proper height, put the toespace cover back on, secured the top of the unit to the underside of the countertop and I was good to go. No more water leakage.

Old baffles lift out and new ones installed - very easy

Removed the old one from its slot and slid the new one into it.
No instructions needed.

I used the website to identify a few different problem areas. I found that the motor shaft would not turn. Upon removing it, it did turn, which lead me to look at the Impeller which was worn / frozen. Ordered new impeller and installed 100 % success !!!

Ordered rubber connector and it arrived the next day. Shut off main power and water. Disconnected water supply and pulled unit out from under counter. Flipped unit over on it's side. Disconnected wiring, drain hose, clamps and completely removed motor/pump. Rubber connector would not unscrew by hand so I found a drinking glass slightly smaller in diameter than the connector inner diameter. Inserted glass in connector and proceeded to unscrew connector by turning connector and glass together. After removing old connector I cleaned the mating part after removing it from inside the washer and removed all the build-up. Replaced everything back in same order.

Took four screws out, unscrewed the piston & nut assembly by hand installed the new one. Cycled the dishwasher & it worked perfectly.

Repair is super easy and anyone can do it in no time!
At first my fear was that it was the pump, but after reading through the trouble shooting here it narrowed it down to the water inlet valve. The new valve even came with easy to read and understand instructions. I had it fixed in less time than it took my wife to make us lunch lol.

2 screws hold the mount bracket in place. Just remove the screws, remove the c-clip that holds the secondary/small water line on, pop the hose off then remove the main water inlet line [ its the bigger line with the brass fitting ] I only needed a pair of pliers for this. Reinstall the main water line into the new valve, but make sure you use pipe tape on the fitting or you'll have a water leak. Reinstall the secondary water line and reclip the c-clip using pliers to squeeze the clip. Hold the valve in place and reinstall the 2 mounting screws. That's it your done !!

This is the second time I've used partselect, and they are hands down the best !! Other sites would have you buying part after part until you happened to get lucky and get the right one. Not here, they help you figure out just what you need and nothing more.
Great people and fast service !!
Thank you once again.

I disconnected the electrical wires. Then disconnected the support strut and the two hose clamps. I was then able to remove the motor /pump assy where I completed the disassembly of the solenoid linkage and pump assy. I removed the solenoid shaft seal. I disassembled the impella parts & the motor shaft seal. I reassembled using new seals, impeller, and grader nut. The only tricky step was waking up to the fact of a left handed thread on the grader nut. I re-installed the motor/pump unit, tightened the hose clamps, connected the electrical wires, & support strut.