36314192992 Kenmore Dishwasher - Instructions

Snapped right in

Determined not to call a repairman for such a simple problem, I watched your extremely helpful video. The ordered parts came right away and all it took was a screw driver and 30 minutes to take off and replace four rollers. So easy, this 75 year-old grandma could do it!

installed new rollers per diagram then installed side ends into sides. Couldn`t have been easier. Dishwasher is like new now.

I first made a bad assumption that the leaking dishwasher was from the gasket. I replaced the gasket and it still leaked. To find the leak, I took the body off of the dishwasher and ran it to find the leak. It was from the solonoid connection. I took photos of the leaking motor unit and very easily replaced the new motor unit by matching the placement from the photos. The hardest part is tipping the dishwasher on its side and mopping up the water.
It was very easy. All you need is a nut driver and a Phillips screwdriver. Even an over-domesticated, non- tool user can do it.

easiest way i found to do it was pull dishwashers out from under the cabnet... laided a pillow down in front of the door and turned it on the front side... the part was very easy to get to at this angle....could have done it in less then 5 minutes but took my time to double check everything to be safe....took a total of about 10 minutes..... very happy now no longer need to vacume out the old dish water left at the bottom of the dishwasher...... i think most anyone could do this very easy....

Ordered the new motor/pump here at parts select and with the easy directions I replaced in no time flat. Saved me $300.00 for a replacement.

Each replacement wheel came in two parts: the wheel itself and the clip which had to be pushed through the center hole in the wheel in order to attach each wheel to the carriage that holds dishes. I had difficulty assembling the clips and wheels until I ran the clips under hot water to soften them. This made it possible to assemble the wheels and attach them to the dish carriage. I would have preferred the wheels to have come assembled, particularly given the price of each one.

The video was extremely helpful. Removing the tabs was easy. However, we struggled with the re-insertion. They did not "snap" back in as easily as seen on video. We ended up using a pair of pliers to push pieces into slot. We did not use very much pressure for fear of breaking the plastic. However, after many tries, we were successful & it works perfectly. Perhaps a close-up of the "snapping in" part might help future installers.

Our older GE dishwasher was leaking water on the floor while running. After inspecting it while running I was able to determine that the water was coming from the seal around the motors shaft where it entered the pump. I then looked up the washers model number and ordered the impeller shaft seal kit. To my suprise the kit arrived the very next day! After disconnecting the power and water supplies from the dishwasher , I then removed it from the cabinet base and turned it over to gain easy access to the bottom. Using nothing more than a nut driver, adjustable wrench and a pair of pliers I was able to loosen the two compression clamps and two hose clamps that hold the pump to the bottom of the washers tub. I then removed the entire pump and took it to my work bench for the rest of the repair. Removing the plastic impeller strainer was the toughest part.. Lacking the proper spanner wrench, I had no tool that would lock onto the raised tabs to turn it loose with. I was able to position the tabs in the jaws of my workbench vise and giving the entire pump a little twist, It broke free and I was then able to unscrew the rest of the way it by hand.. The old dried up detergent made for a good adhesive, and after removal I cleaned the area completely so the new strainer would thread in easy. I installed the new parts in the kit as per the supplied instructions and re-installed the pump housing back on the dishwasher and put it all back in place. After running it several times not a drip was to be seen, and I was very pleased with the whole process. With the shipping it cost me just $25.00, and it saved me a expensive service call or maybe even the cost of buying a new machine. I would say that overall it was a easy repair but lacking the right tools, you may have some trouble removing the pumps plastic strainer screen as I did. I would highly recommend PartsSelect to anyone, and the entire experience was a good one for me.

Removed rack slide end caps. They broke off because of brittleness. Removed rack, then used pliers and/or flat blade screwdriver to remove 4 rollers and axle assemblies. Replaced with new rollers/axles. Return upper rack into slides and installed new end caps. New caps slightly different than old but easily clip into place Upper rack works lile new!

I watched several YouTube videos on how to make the repair. It looked very easy but sometimes professionals, because they've done it before, don't point out small tips that would help a DIY homeowner. The latch goes easily into the inner door slot but there's nothing to hold it there. The videos show the inner and outer door being closed together without showing that you have to hold the latch in place while bringing the outer door up to meet the inner door. Any movement of the inner door makes the latch fall out. So I would say it took me 5 times longer to do this repair than it would if I was doing it again.

The wheel kit came with axel's to support them. They snapped in place in seconds. No instructions provided, but installing method was obvious.

It was really simple. I watched the u-tube video to replace the top rack. I was able to complete removal of the old one and replacement with the new one in about 5 minutes. The lower rack simply pulled out and the new one slid right in. The quality of the replacement racks is much higher than the originals. I'm so happy I chose this easy and cost efficient repair.

The new rollers snapped into place on the rack, by simply pushing them in. I was able to do it by hand, my wife could not do the same, so you might use some pliers.

Removed the lower rack. Took off the old wheels. Put the axles on the new wheels which took a little manpower, but became easier once you did a couple (there are 8 wheels). Then snapped the new wheels on the rack which was really simple. The new design is much improved to the old one. The wheels glide better, then they ever did. We're sorry we didn't think of this repair years ago and the cost was a fraction of the cost of a new dishwasher.