All Installation Instructions for Kenmore Dishwasher 36314181200

NONE

UNPACKED WHEELS AND CLIP. USING NEEDLE NOSE PLIERS SQUEEZED WHEEL TIP TO INSERT IN WHEEL. REMOVED OLD WHEELS AND RETAINER BY HAND. INSTALLED NEW WHEELS INSTALLED AND NEW RETAINERS

Parts Used:

Lower Rack Wheel Kit - 8 Pack

Edward from GRAND BLANC, MI
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Leaked at bottom of door

I took the inside of door off to install both gasket and gasket insert. Much easier this way. Also it’s much easier to fish locking handle through the door if you extend the handle half way and put through opening when raising the door.

Parts Used:

Door Gasket - White

Harry from CLEVELAND, OH
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

door latch broken

I watched the convenient video and saved an old machine that I've grown to love. Plus I didn't have to pay a repair service or have to buy a new machine.
Thanks GE,
T. Dunn

Parts Used:

Door Latch Kit

Thomas from COLUMBUS, GA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

The pump shaft leaked

I used the pump/motor replacement kit. It was a very easy repair and the parts were a direct replacement with no modification necessary. I saved over $300.

Parts Used:

Motor and Pump Kit

Phillip from Canton, GA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers, Socket set, Wrench set

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Couldn't drain water

I connected one end of hose to the drain using a hose clamp and screwdriver then connected the other end to the dishwasher using anouther hose clamp and a screwdriver..

Parts Used:

Drain Hose

Janice from Rockville, MO
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

4 of 9 people found this instruction helpful.

Was this instruction helpful to you?

Water not draining.

Removed the 4 screws on front inspection plate and had easy access to solenoid switch. Unplugged unit and switched out with repair kit. So easy a caveman could do it...

Parts Used:

Drain Solenoid Kit

Eric from Mayetta, KS
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

The dishwasher would not drain water out.

I removed 2 screws a wire plug connector and replaced the old part. The total repair including putting the cover plate back on only took about 15 minutes. Also I saved approximately $130.00 by doing this repair my self.

Parts Used:

Drain Solenoid Kit

Rick from Rimersburg, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Socket set

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

dishwasher did'nt drain water . solinoid was melted and stuck

First I removed the two screws that hold the solinoid in place,then I removed the e clip and unpluged the wire and pulled out the plastic lever with the solinoid and springs. To install Solinoid:First I bolted on the bracket ,then I hooked in the spring in the plastic lever and installed lever on shaft then I hooked in the long spring to the bracket small hole in the bottum then I installed the e clip next I pluged in the wire.Then I tried the Washer .Averthing works fine.

Parts Used:

Drain Solenoid Kit

Ben from florida, MI
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Won't drain,Won't fill, float switch good. After installing timer it worked once. decided to replace the whole dishwasher

Remove the back of the front panel. Replace timer held by 2 screws and 2 elec. connectors.

Parts Used:

Timer

merritt from venice, FL
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

replace door gasket

from the information previous customers had written.
it saved a lot of fustration and time
and best of all the dish washer does not leak.

Parts Used:

Door Gasket - White

forrest from stuart, FL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Dishwasher would not drain

Ordered motor and pump and replaced. Motor pump kit also comes with a drain solinoid so if that was the problem the kit repaired it. One issue is the size of the hanger to ensure the pump does not just hang on its mount. The directions were not very clear and after some trial and error I got it to work to.

Parts Used:

Motor and Pump Kit

kevin from wellington, FL
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers, Wrench set

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Pump/Motor leaking at shaft

This was one of those wonderful repairs where anything went right.
The part arrived overnight as ordered and even though I was abit leary of it fitting, since it was described as a replacement/new design, it fit perfectly! As mentioned in another post here, draining the water out of the unit so I could tip it over to do the replacement was the hardest part!
I'm sure I saved over $100 doing it myself. Thanks PartSelect!

Parts Used:

Motor and Pump Kit

Brett from Sound Beach, NY
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

leak between motor and pump housing

repair kit was complete and directions were easy to follow. my model of dishwasher disnt even require any of the adapters. really only required removing a couple of clamps and replacing everything as a single unit

Parts Used:

Motor and Pump Kit

kevin from longmont, CO
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Water would not drain out and keep filling up sprayers work

Your video doesn't include disconnecting water supply disconnecting electrical and disconnecting drain hose but after all that the repair to change the solenoid was a easy task but the problem was not solved so I TRIED . thanks Robert

Parts Used:

Drain Solenoid Kit