36291208000 Kenmore Range - Instructions

First I removed the burners and pulled the stove out to get the back cover off. Removed the back cover after main power was shut off. Removed old burner terminal blocks and replaced with new ones. Replaced back cover and pushed stove back into place. Turned on main power to stove checked burners and they worked. DO NOT REPLACE OR DO ANY ELECTRICAL WORK ON ANY MAJOR APPLIANCE WITH OUT FIRST TURNING OFF THE MAIN POWER SOURCE.

Received complete burner receptacle. Decided to take off stove back to plug in directly to burner control.
Turn on stove on low. No heat. Bad coil element. Checked for power at coil element. Switched another burner. It heated immediaetly. Have to order or find a burner element

Shut the power off and unscrewed facial hardware ,unplugged terminal and unscrewed hold down bracket and redid everything that I mentioned above. For a rookie it was a piece of cake.

Pull out the range. Pull out the electric plug. Unfasten the back panel. Raise the range top. Replace the terminal block in exactly the same position as the old one. Put everything back.

This is the third time I have replaced it so it is very easy now. This time I spent a little more time making sure the burner element prongs were just just like the others. Must have been a little loose in the block.

I first unpluged the stove then removed the 6" element then I removed the back panel on the stove located the wires that went to that element unplugged them and removed the block then fished the wires through for new terminal block installed in terminal block bracket then pluged in wires put element in place put back panel back in place plugged stove checkout heat on element good to go 20 min

I have a GE Profile oven and the heating element on the bottom broke in two. I found the part on your website very easily. It was easy to see that I had the correct part. I ordered the new element and it came in about three days. I easily took off the old element, but I was really surprised because the new one didn't fit. The heating element itself was the correct size, but the holes didn't quite match up. As a matter of fact I had to take some tin snips and expand the hole at the back of the oven. That was the only hard part, but it was really difficult to lean in that far without putting too much weight on the door. Anyway, I opened the hole about an inch more, plugged it in, and now it works perfectly!

Removed to screws on bracket and sliped the element out. Inserted new element and installed bracket and two screws.

turned electricity off, removed element using a screwdriver had to take the back panel off, attached new element put stove back and tried it out and it worked probably 20 minutes. Also need to comment that was totally shocked how fast the element was shipped to me, ordered the part in the p.m. and it was here not the next day but the next ....awesome

First we removed the screws inside the oven. Next, the oven backing was removed by unscrewing one side and one bottom bolt which exposed the clips for the burner. The clips were removed from the old burner. The old burner was pulled through the fiberglass protection and out of the oven. The new burner was inserted into the oven and the prongs were pushed through the fiberglass protection. The screws inside the oven were reattached. The clips were attached on the outside of the oven. The backing was slid into the right holding piece and the bolts on the left and bottom were attached.

removed element found a crack and replaced with new one I got from PartSelect.com. with fast fast shipping,thanks you saved me for spendin more money on a new one. it happened on christmas day of course......

Nylon support is attached to the oven frame with a screw having a .25 inch socket head. The screw is mounted in a recessed opening on the support, so a socket is needed. I needed to purchase a proper size socket from the hardware store for a few dollars since the smallest one I had was 7mm. I guessed at the size and was correct. Repair was easy and took a few minutes.

This one is a really easy fix as I only had to plug the burner element into the slot. I was very pleased with the speed of the order and would order again if I need parts.

Thanks,
Cheryl

It was as easy as you said. I took the back off, removed the screws holding the terminal, un-hooked it and put the new on on. Replaced the back and wa-la! Working burner

Disconnected power supply to range, pull top back metal cover, pull wires from burner on/off switch,and removed one screw that holds block in place. Installed new terminal block by placing screw back on block & placing wires back on the on/off switch.

The repair was very simple removed old element by removing two screws and disconnecting the element from the wires and reinstalling the new one.