36273281891 Kenmore Range - Instructions

You need to remove the knobs and remove the panel where the knobs are connected.

You also need to remove the display panel front to gain access to the where the electrode wires attach.

The other screws are readily visible. It's about 30 screws that need to be pulled.

The adapter put on the electrode can be pulled off with needle nose pliers and a small screwdriver, if the adapter does not fit through the opening on your stove. Just put the adapter back on after you snake the wires through.

I followed the video instructions on the site. I unplugged the power supply and turned off the gas supply. I then removed the plate out of the bottom of the oven to get to the igniter. Then I removed the screws and unplugged the igniter to remove the old part. I had to purchase two porcelain wire nuts because the new part connection did not match up with the old connection. The repairs were quite simple and I had my oven back and working in no time. I am glad I read the comments from others because I thought it was my gas control valve, but they were right it was my igniter. This saved me time and money.

Unplugged the stove and pulled it out from the wall. Took the metal shield off the back of stove held by 2 screws. Unplugged the Molex connector for the igniter. unscrewed the round metal shield covering the opening where the igniter wires run to the back of the stove. Removed the 2 screws that held igniter bracket to the burner. Next, I pulled the wires and Molex connector through the opening. Installed new igniter in the reverse order. Be very careful with new igniter as they are very fragile and can break easily.

I thought I was being a total girl and was afraid of fixing my oven myself, but when it took forever to get my landlord to come over and fix my oven I ordered the part, got it in three days, followed the directions online and fixed it myself! Easy, easy! Turned off the electric, switched off the gas, unscrewed 2 bolts, unplugged the old switch, screwed in the new switch, replugged it and turned on the stove. Roasted a chicken and baked bread within minutes!

Removed the screws that held the shield in place. Then unplugged the igniter and removed the 2 screws that hold igniter in place. I had to cut the connector off the new igniter and wire nut the old connector on because of a different connector.
I then put everything back together and ooolaalaa, it worked!!!!!!!

Thanks for the quick service,
Tom

Removed oven racks, removed lower oven shelf panel by using a flathead screwdriver and removed two screws on the back edge of the panel. Removed flat style ignitor (two hex head screws)from the gas burner tube using a 3/16 nutdriver. Disconnected two wires from the ignitor. Removed the two pin connector from the new ignitor, stripped the insulation to expose about a 1/4 inch of bare wire at the ends of the wire where the connector was removed. Installed the ignitor to the gas burner tube using the 3/16 hexhead screws. Connected the wires using porcelain wire nuts. Re-installed the lower oven shelf panel, flathead screws and the oven racks. Oven worked as advertised.

I deturmined that the flame starter was not pulling enough amps to open the gas valve (safety valve) . pulled two hand screws and removed floor of oven exposing the flame bar and flame starter. removed two screws on flame starter. removed lower pan drawer and disconected the electrical plug for flame starter. replaced in reverse order. easy.

I found that it was a little easier to pull out the stove to do the electrical connections. First I pulled out the stove being very careful not to bend the gas line. I pulled out the wires and disconnected them. I removed the 2 screws that hold the igniter and compared it to the new one it matched. I hooked it back up with the 2 screws then did the wire connections pushed the stove back carefully and tested the new igniter it worked like new no more microwave dinners thanks parts select .com

First I removed the racks and oven bottom panel. Then I took out the two screws holding the ignighter unplugged the wire connection and removed the old ignighter, compared the old with the new one mounted it back with the two screws plugged it back in. Job finished in 15 minutes and oven back working again.

I removed the broken glass and scraped the edges to remove any excess. Then I slipped in the new glass and used the hammer to bend back the edge that holds the glass in place. Your company and website made it very easy for me to find and order the part I needed to repair my oven. Also, I saved about $30 compared to the quote I received from my local appliance store.

Took it out of the box, lifted the stove lid and replaced the part, no tools required. Very satisfied with the shipping and the part, great service. Thanks!

remove the door,racks,cover over burner,burner,element,replaced element and rest in reversed order.

First I removed the botoom drawer.
Second, removed three 1/4 in (head size) screws and removed the reflector pan from the bottom of the oven.
Third I removed the three racks in the main part of the oven and then the two slot head screws that retain the oven floor. I then removed the oven floor.
Four, now that I had access to the ignitor, I removed the two 1/4 (head size) screws that mounted the ignitor to the burner.
Fifth I disconnected the wire plug which is located in the lower section of the oven. I was unable to route the wire with it's connector on out of the oven, so I just snipped the wires and took it out in two pieces.
Installation was just the reversal of this with the obvious exception of snipping the wires. I was able to route the wires differently so that I did not have to pass the connector behind any restrictions.
Finally afte all was reassembled, I did an ops check and everything worked just fine.

To get to the element I had to remove the lower cover from inside the oven.

After that I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the wires. The wires are accessible from behind the undertray.

Installation of the new one was simply the reverse.

Before re-installing the burner cover I did a quick test to ensure the new igniter functioned properly and that I hadn't mis-diagnosed the problem. The element quickly started to glow and that was it.

The oven now works as it should.

had to take back off of oven because of the connector and the plug end insert had the wrong pin so i had to take it apart and use old ones then i put the assembly in /and put oven back together