36262781003 Kenmore Range - Instructions

Nicholas from Poynette, WI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Element went bad

turned electricity off, removed element using a screwdriver had to take the back panel off, attached new element put stove back and tried it out and it worked probably 20 minutes. Also need to comment that was totally shocked how fast the element was shipped to me, ordered the part in the p.m. and it was here not the next day but the next ....awesome

Parts Used:

Steve from Blue Hill, NE
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

The bottom burner melted

First we removed the screws inside the oven. Next, the oven backing was removed by unscrewing one side and one bottom bolt which exposed the clips for the burner. The clips were removed from the old burner. The old burner was pulled through the fiberglass protection and out of the oven. The new burner was inserted into the oven and the prongs were pushed through the fiberglass protection. The screws inside the oven were reattached. The clips were attached on the outside of the oven. The backing was slid into the right holding piece and the bolts on the left and bottom were attached.

Parts Used:

Linda from Virginia Beach, VA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

bakeing element burned out

Removed to screws on bracket and sliped the element out. Inserted new element and installed bracket and two screws.

Parts Used:

Bob from Surry, VA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

The element started to spark and actually broke into two pieces.

I have a GE Profile oven and the heating element on the bottom broke in two. I found the part on your website very easily. It was easy to see that I had the correct part. I ordered the new element and it came in about three days. I easily took off the old element, but I was really surprised because the new one didn't fit. The heating element itself was the correct size, but the holes didn't quite match up. As a matter of fact I had to take some tin snips and expand the hole at the back of the oven. That was the only hard part, but it was really difficult to lean in that far without putting too much weight on the door. Anyway, I opened the hole about an inch more, plugged it in, and now it works perfectly!

Parts Used:

Joe from Austin, TX
Difficulty Level:
Very Difficult
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Bake element burned out

Was a piece of cake removed 2 screws, pulled element out. Pulled the wires ooff the old unit and put them on new unit and screwed it back in.

Parts Used:

Barry from Malvern, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

no heat in oven

removed element found a crack and replaced with new one I got from PartSelect.com. with fast fast shipping,thanks you saved me for spendin more money on a new one. it happened on christmas day of course......

Parts Used:

ronda from kingston, OK
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Open door. Put racks in.

nothing to it.

Parts Used:

Oven Rack

Harriet from Jacksonville Beach, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

needed "original style" on older stove

I needed to replace all stovetop bowls and found all after-market bowls "just a little off" effecting how flat the burner rested so called PartSelect's hotline and was assured that if I were using the actual model number found on the stove the parts would definitely fit and not almost fit, guaranteed, and they did!

Parts Used:

David from N. Fort Myers, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Found out Drip Bowls can not be added to self-clean

Dropped in new bowls. I was surprised how in-expensive new ones were.

Parts Used:

Gary from Renton, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Bake Element Broke

followed the instruction from your video an it was a snap

Parts Used:

Lesley from LaPlace, LA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers

Was this instruction helpful to you?

Disgusting looking burner drip bowls.

Just had to change out the drip bowls, easy. But, I wanted to comment on the quick delivery on the new bowls. I was impressed. Thank you.

Parts Used:

Constance L from Woodhull, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

none

Took the old pans out and put the new ones in. Simple as pie

Parts Used:

Leslie N from Carson City, NV
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Bake element buned and broken

The repair was somewhat easy. The replacement elements are pushon type. The only thing is that the G.E. Hotpoint wire on the right side of the bake element is short. Be extra careful to not have it go back into the back oven wall or you will have to take the back cover plate (Pull out the range, remove the back cover using a nut driver or a magnetic tip srewdriver with the bit removed works[Wires are right there]. This is as easy a job as can be.

Parts Used: