All Installation Instructions for Kenmore Range 36262780100

burn out switches

Pull stove out from the wall unplug it remove the old switches and replaced them withe new one. they work just fine.

Parts Used:

Thomas from Hinesville, GA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set

Was this instruction helpful to you?

Oven would not reach bake temp.

Used the TS guide, because I had no idea what the problem was. That was easy step by step. Thanks. Gave me a list of two parts that could fix the problem. Picked the higher percentage part (97%). Followed the simple install instructions and it was successful. One problem I did encounter was the two wires that it connected to were short. Removed the back center plate to gain access to the wires. I was able to extend them enough to make the connections to the bake element. If not for that the repair would have only taken maybe 10 minute's.

Parts Used:

Bake Element

Thomas from Rogersville, TN
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers

Was this instruction helpful to you?

The burner would not work.

I pulled the range out, unplugged it, took the back off, unplugged the old terminal block and removed it. Attached the new block and ran the wires through to the back and plugged them in. Reattached the cover on the back of the range, plugged the range back in and pushed it back into place.

Parts Used:

Surface Burner Terminal Block Kit

Sue from Fort Oglethorpe, GA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Bake element not working

Removed element with 1/4 " nut driver, unhooked element,started to install new element and discovered the wires were too short and had to remove cover on the back to replace wires on the new element. The wires on my range were not as long as the ones showed on the video.It was still an easy repair and the delivery time was less than 2 days. excellent service. Thanks

Parts Used:

Bake Element

Rodney from Chambersburg, PA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers

Was this instruction helpful to you?

Wires to attach to bake element retracted into stove body

I had to remove the back panel on the stove to free up taped wires to get more length.

Parts Used:

Bake Element

Michael from Hamden, CT
Difficulty Level:
Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers

Was this instruction helpful to you?

2 mounting bracket included, wires too long

I couldn't tell which one work best till I installed 2 units and I liked the other bracket for stability.The wired were too long and there is not a given way to strap them and keep them away from the heat source.

Parts Used:

Surface Burner Terminal Block Kit

Fuad from Sarsota, FL
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers

Was this instruction helpful to you?

Burner wouldnt heat

Watched video,and used it as guideline.Biggest problem was removing tape from old wires.

Parts Used:

Surface Burner Terminal Block Kit

Mary from Leon, KS
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver

Was this instruction helpful to you?

Old bake element burned out

Turned off circuit breaker, removed screws holding old element in with nut drivers, pulled out old element about 3-4" to reach terminals connected to back of element, removed spade lug terminals with needle nose pliers. Reconnected terminals to new element and screwed new element in place with nut drivers. Turned on circuit breaker and oven. New element works perfectly. Took about 8-10 minutes. Very easy to do.

Parts Used:

Bake Element

Thomas from Hamilton, VA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers

Was this instruction helpful to you?

Rusted out burnner bolws

Remove old burnner bolws and install new ones

Parts Used:

Drip Bowl - 8 Inch

Drip Bowl - 6 Inch

charles from ft.pierce, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Broken bake element

Very easy to install save several dollars

Parts Used:

Bake Element

Marcus from Lagrange, GA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

Was this instruction helpful to you?

needed to unstall "anti tilt" bracket on back of electric range to be code compliant for property..

Turned off circuit breaker, Then pulled out range, straight out and away from wall and cabinets. Layed braket on flooring and moved stove back in to make certain it aligned with range rear stands. Moved range back out, marked holes in braket, screwed in screws to anchor bracket. Pushed range back into placed against wall. Tried to |"tilt" range by pulling down on door after opened - range was held in place sre

Parts Used:

BRACKET ANTI-TIP Assembly

Greg from Ft. Washington, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

needed new drip bowls for stovetop GE

removed the burners and dropped the drip bowls in. Very easy to do,

Parts Used:

Drip Bowl - 8 Inch

Drip Bowl - 6 Inch

Patricia from Centereach, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Burned heating coil

Just pulled old coil out of the plug. Replaced drip bowl and inserted new coil in. No problem.

Parts Used:

Drip Bowl - 6 Inch

Surface Burner - 6-Inch

Maria T from Germantown, MD
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Old dishwasher rack and silverware rack

The whole process was very easy! I just got the model number and bought a new rack and silverware holder on,one. There was no assembly needed so I just popped them in and replaced the old ones! Very easy to do!

Parts Used: