All Installation Instructions for Magic Chef Range 35HA-92X-ON

old drip bowl was worn out

new drip bowl fit perfectly and was a snap to install.

Parts Used:

Richard from Germantown, MD
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Oven light Switch

Compressed the springs and removed the damaged switch, then changed the wiring over to the new switch and press into place, worked fine.

Parts Used:

SWTCH-LITE

William from APACHE JUNCTION, AZ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

Was this instruction helpful to you?

The drip pans needed replacing.

Put in the new drip pan -- which are really nice shiny ones.

Parts Used:

Chrome Drip Bowl - 8 inch

Drip Bowl - 6 Inch

Alison from Carnation, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Dirty drip bowls

Just remove old bowls from range top and put new ones. That is all ... just super simple! :)

Parts Used:

Chrome Drip Bowl - 8 inch

Drip Bowl - 6 Inch

Paul from Carnegie, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Dirty drip bowl

Remove old drip bowl from the range and put a new one back.

Parts Used:

Chrome Drip Bowl - 8 inch

Paul from Carnegie, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

drip pan were burnt out

simply remove the burner take out the drip pan and bowl individually. Install the new one and replace the burner. no tool was used.

Parts Used:

Chrome Drip Bowl - 8 inch

Drip Bowl - 6 Inch

Delroy from Miramar, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Oven would not heat up properly to set temperature

The element appeared to have been damaged. I replaced the element with ease. However, I still have the same problem. The oven does not heat up to the set temperature. Information from the part select website is that it is more likely the long oven sensor. I ordered one and will provide the results after I have this sensor replaced with a new one.

Parts Used:

Bake Element (15 Inch long x 19 Inch wide)

Max from Bothell, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Easy installation

Unplug stove from outlet!! Removed screws (Phillips head) from prior element and pulled out enough to slip of the red and white wires. Keep in mind which side which is on and take old element out of oven. Put new element in and attach wires back on the same sides. Push back in and use screwdriver (Phillips head) to lift insulation to push wires and element prongs back. Put screws back in, close oven door and plug stove back in. Tested and works great!

Parts Used:

Bake Element (15 Inch long x 19 Inch wide)

Jeremie from Freeland, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Light bulb failure

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

Parts Used:

Light Bulb - 40W

Grant from Alexandria, VA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Burners quit working

Bought two new replacement burners,they work great!

Parts Used:

Economy Y-frame Surface Unit - 6"

Economy Y-frame Surface Unit - 8"

Brenda from Brazoria, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

The original bake element burned out

1. Removed racks 2. Removed two screws holding in the bake element. 3. Gently pulled out the element exposing the two wires connected to it. 4. The two wires were held by a clip connection. 5. Removed the wire clips holding the wires. 6. Attached the clips to the new element and re-installed the element. New problem: The element did not heat up. A repairman informed me that the selector switch was damaged during the burnout- that switch was no longer manufactured and was discontinued. Whirlpool company was checked and indicated that there was a new part # 7403P023-60 but that was discontinued too. I was able to get the element working by moving the selector switch to the "Bake" position and then moving the switch about 1/4" in the clockwise direction. The element heated and the oven works at least for now as I search for a replacement part. PartSelect was an invaluable aid and helpful all along the process.

Parts Used:

Bake Element (15 Inch long x 19 Inch wide)

William from Florissant, MO
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

Broken Door Spring

Slid oven out from counters. On each side there are 3 screws on the front and three screws on the back holding the side piece on. Once off, the spring was very easy to get at and replace. I had only one broken, but replaced both anyways. I think it took longer to clean the sides of the oven that haven't been touched in years than to replace the springs. This job was very simple and easy.

Parts Used:

Oven Door Spring

Matthew from Chippewa Falls, WI
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

needed a new drip bowl and couldn't find ons that fit exactly but you had it

I removed the old one and put in the new one. Works great!!!!!!!!!!!!

Parts Used:

Chrome Drip Bowl - 8 inch

Elsie from Garner, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

To Old Needed To Be Replace

Actualy I just removed the old ones and replace them with the new ones . And thank you for your prompt delivery I found some one I can trust . Thanks again . Mrs bolanos

Parts Used:

Chrome Drip Bowl - 8 inch

Drip Bowl - 6 Inch