31315VBM Magic Chef Range - Instructions

I located the temp sensor (top left). Removed the 2x Phillips screws and slide the wire out until the plug is thru the opening taking care not to pull to hard as to damage the end that you not going to replace. To install plug it in and push the wire thru and secure with 2x Phillip screws.

ordered new replacement oven igniter kit and also felt it was a good opportunity to change the oven temperature sensor so also ordered short oven sensor kit. both parts fit as described as original replacements with very little work involved. oven worked properly good well done and a big saving on a service call repair or new range.

New parts matched up perfectly. Undid screws holding old igniter, hardest part of procedure because one screw was frozen and broke off. Pulled stove out and new igniter"s connector was identical. Pushed stove back into place and it lighted on the first try.

using the diagram shown on line Looked up the ignition module and ordered it by phone. Received it the next day and installed it within the hour. Previously I had called the repairman and he said it would be a couple of weeks before he could look at it and a service call was $75 plus parts..I fixed it for the cost of the module $34. I am very satisfied.

Removed bottom tray of oven, unscrewed gas pipe, removed old igniter and replaced it. Spent some extra time digging around for leads, etc. before discovering that my new igniter was identical to the old one and all I had to do was plug it in.

removed old socket and replaced.
I was VERY pleased with Partselect. Easy to find part, it was in stock and fast delivery.

The ignitor heated up and the broiler worked but not the bake mode. Repaired per instructions

UNPLUG THE POWER CORD! This particular model is a (slide-in) unit, it was wedged between to fixed cupboards/cabinets. Therefore, there are really no side panels to speak of, this made the repair slightly easier. I simply slid the unit out enough to unplug the power cord and access the right side of the unit. All one needs, at this point, is a Phillips head screw driver to remove a small metal panel installed just below the stove top panel (right side of range), its held with approx. 8 screws. There is one other panel that must be removed as well, (you may want to remove this panel first). It is an enameled-like panel approx. 5" wide x 36" long located at the front of the range (right side) running the length/height of the range (held with 2 screws). Get those 2 panels removed and you will see the spark module attached near center of range just under stove-top panel. Module is attached to a small metal bracket, module has 6 wires attached to it (2 feeding the module and 4 exiting the module to the burners). Bracket screws are nearly impossible to get at (you need a very stubby Phillips screw driver, if you can even get your hand in there). Anyway, I simply released the module from the bracket, then carefully bent the bracket back toward me; to provide work area for my hands. The bracket bends easily and really can't be broken. Now, at this point (using longer needle-nose pliers) detach the wires from the old module (remembering each wires location) or, as I did, hold the replacement module near the existing module and transfer the wires one at a time. Now, slap it all back together as you took it apart. Really simple job, total time is easily/generally under 30 minutes. It may be easier to access the module by removing all the burner components and raising the stove-top? Not sure? I chose not to do the repair that way. Hard part was locating where the manufacturer hid the module on the range. :- ) D.I.Y.ers Rock!!!

I first removed oven racks.then I removed bottom of oven by sliding locks,then lifting out bottom.Next I removed screw holding e. control cove,then removed cover.Igniter plug was exposed,I then unpluged egniter. I next removed 2 screws holding burner and igniter .I removed igniter and burner as a unit. removed 1 screw from igniter,and replaced igniter on burner.Then assembled every thing in reverse order,and tested Oven worked perfectly.

Removed all the racks from inside the oven, unscrewed the 6 screws that held it into the cabinet, pulled it out and sat it on the floor in front of the cabinet. Removed the oven sensor from the inside of the oven after disconnecting the wire harness from the rear right exterior of the oven. Installed new sensor from inside (2screws), plugged it into the harness in the back and reinstalled oven in the cabinet.

Unplugged the old temp sensor at the back of the stove. From the inside I removed the 2 retaining screws. I taped a string to the old wire and pulled it through so I could pull the new harness through on the new sensor. When the new sensor arrived I installed it in reverse order. Easy peasy. Works great!!!!

I took the broiler pan out of the shipping container and put it in the oven.

I first switched the old burner to a new position and different ignitor wiring. The problem persisted in both places, so I bought a new burner assembly and now the burner lights immediately. Very happy and a very simple replacement.

It looked like an easy fix. the igniter had a plastic clip. A simple R&R. Removed old igniter from its mount, removed plate to get access to wires, removed insulation. Tried to pull the old wires out of its location. It was hung up and I spent 1/2 hr. trying to free it. No go. I thought I'd have to remove oven from its cabinet. I removed six screws and it would not come forward. I felt the under side of the oven thru lower door of cabinet and found out that was where gas was connected. No way was I disconnecting the gas. Pushed oven back in, reinstalled screws and decided to cut old wires and splice in the new igniter. WENT BACK AND READ THE INSTRUCTIONS! Supplied were 4 ceramic wire nuts. Then the light bulb went on! OKAY! I got a marker and marked the top wire on the old igniter to identify it after I cut the wires as close to the back of the old igniter as I could with a pair of side cutters. I then cut the wires as close as I could to the plastic clip on the new igniter. Striped off 3/8 in. from all wire ends and spliced the wires together using the wire nuts. I stuffed the wires as far as possible back into the hole they came from, replaced all old and some new insulation into the hole. The supplied cover would not work, screw holes would not line up and would have fit poorly. I reused the old hole cover. Screwed new igniter to its mount. Turned on the oven and thought I screwed up. I waited about 30 seconds before I saw it start to glow. WHEW! I got it right! After a few more seconds, the gas came on and the oven burner ignited. The really hard part was putting the oven door back on its mount. That door was heavy and wouldn't line up on the first try.......
Maybe if I read the instructions thoroughly the first time before I started, I could have cut my time in half and saved a lot of cussin'. CUTTING THE WIRES WAS AN "OPTION"! That's why they supplied the ceramic wire nuts!....... Dinner is in the oven right now. Smells good!

Removed grates and bottom plate two screws holding it. Turn oven light on and unwire the wire. Unscrewed the two screws and replace. This took my husband about ten min. And for him he says that this was a walk in the park. He says if he can do it anyone can. This was one of the easy honey dews. Good luck with yours. Nola & keith