3121WTW Magic Chef Range - Instructions

removed oven floor, removed two screws in element . pulled out element wires, secured them so they would not fall back into slot, snaped in new element . scewed it in place , replaced floor . thanks partselect.com

First I removed the two screws that held the old element in place. I then pulled the element out about 3 inches and disconnected the two wires.
I replaced the element with the new one and tucked the connector in the insulation. Additional insulation came with the kit. I replaced the two screws that held the element in placed. Oven worked perfectly

1. Unplugged power cord and remove bottom oven tray.
2. Disengaged plastic connector from the back of the diverter valve.
3.Unscrewed two screws, holding present igniter.
4.Cut two wires, coming from the old igniter, with wire cutter (pliers).
5. Discarded old igniter assembly (in two parts -igniter and connector).
6. Attached connector part of new igniter to straightened coat hanger with insulation tape.
7. Fed the coat hanger from inside toward range back side by slightly displacing present oven insulation.
8. Removed coat hanger when got through.
9. Re-fastened new igniter with old screws.
10. Re-plugged plastic connector into diverter valve.
11. Re-plugged power cord and replace bottom tray.

Tested performance and am totally satisfied with the component and seller's service. There was no need for the extra materials in the kit.

Removed bottom plate from oven enclosure.
Removed the two screw holding the burner in place. Disconnected plug to element, making sure wire did not fall back into underside of oven.
Removed heating element. Replaced element & reinserted burner assembly into oven. Checked oven operation before reinstalling bottom plate. Oven ignition was less than 15 seconds with over one inch flame from burner.

I slide range away from wall, unplugged the electric. Lifted door off the hinges for easy access. The broiler drawer also comes right out. Removed racks and then took out bottom panel. The ignitor is mounted with two hex nut screws. They came out with a phillips head screwdriver. The plug connector is accessable from the rear or the range, there was nothing else to take off. I simply unplugged the connection, pulled the wire through the insulation, screwed on the new ignitor and pushed the plug and wire back through the insulation and plugged it in. The job took less than 25 minutes and that time included cleaning behind, under and inside the range! Oven lit first time it was turned on and works as good as new.

it was so easy my wife could do it!!!!!!!!

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

I found the panel on the innernet, ordered it and when it arrived I removed the old one and replaced it with the new one.

well my brother was over,he said he had the same stove with the same symtoms so we removed bottom tray of oven lifting from the back first then the front.there inback is the igniter.pulled wire out carefully and unplugged and unscrewed 2 small bolt's,replaced igniter remembering it is very fragile,plugged igniter in replaced insulation around wire,saved me from a new oven,thank you partsselect.ps part arrived the next day wow

I removed the oven door and floor, removed the two screws holding the old part in place, unplugged it from the wiring harness and plugged in the new part and replaced the screws. Fixed in 5 minutes.

Broiler lighting fine but main oven burner not lighting. I deduced the oven igniter was most likely the point of failure. Decided to replace empirically rather than time and money for service call. Process was about as easy as replace a computer part. Removed pan and flameguard. Unplugged part from below (after removing drawer). Such a simple plug I didn't bother to throw the breaker / power down the oven. Pulling it out to get to wall plug not an option. Unscrewed old part, saw a flaw had developed in the element. Screwed on the new part, plugged it in, inserted insulation in the hole. Tested for lighting - lit first time. Replaced guard and pan, oven has worked reliably since. Research time was 5x the repair time, but in all a fraction of time and money to have a "pro."

I removed the various trays and racks to gain access to the oven igniter. I removed the one screw that held the wiring in place that goes into the body of the oven and pulled out the wires. I removed the wire nuts and safe ended the hot wires. I removed the two screws that held the igniter in place and replaced it with the new one. I reconnected the wiring with the wire nuts , pushed the wiring back into the body of the and stuffed new packing material into hole and reattached the plate on the back of the oven. Turned on the oven and it ignited immediately. A very easy job to complete. I would suggest to others to turn off the power. I knew what I was doing by working it "hot".

Figured it had to be the ignitor. I didn't use a multi-meter. Since the appliance was so old, if the $50 igniter didn't do the trick, I'd just replace the oven. Install was super easy, and now oven works great!!!

Fist I removed the screws on the front-sides of the oven. Then I turned off the gas, by adjusting the in-line valve. I then unscrewed the gas fitting going into the bottom of the oven. I pulled the oven out, being careful not to put too much pull on the electrical cord. I put a bench in front of the oven and set it down.
I then removed the oven racks, and the plate in the bottom. Bottom element is bake, top element is broil. I unscrewed the igniter, then disconnected its plastic wire connector on the back of the oven, then pushed and pulled the connector into the oven and out the door.
Then I ordered my part for $30 less than Sears from PartSelect, and it got here STUPID FAST. I hooked it up and put everything back together, no big deal, BOOM - Cornbread!

Our oven failed to cook in the Bake mode. I was thinking I needed to have a repairman come service it. I got the product manual & begin to do some research. I thought the problem was was in the control panel until a parts search took me to the Parts Select website where I read the other successful repair stories & the most likely reason it did not work. It was real simple. The only problem I had was a screw that held the ignitor stripped & I had to cut the head off. The directions sent with the part were dead on. I then simply installed new ignitor & presto - it works! My wire connection required stripping the wires & using the ceramic wirenuts. I am glad I found Part Select & will call again when needed!! Thanks !!