3116PRW Magic Chef Range - Instructions

Overall, it was painless and easy with zero problems

Removed grates and bottom plate two screws holding it. Turn oven light on and unwire the wire. Unscrewed the two screws and replace. This took my husband about ten min. And for him he says that this was a walk in the park. He says if he can do it anyone can. This was one of the easy honey dews. Good luck with yours. Nola & keith

Took off the top plate at the bottom of the oven, and the flame spreader, removed 2 screws on the igniter, pulled out the broiler tray and unplugged it. Took longer to get off the floor than it did to replace the part.

Thanks to previous posters, this seemed to be an igniter issue, and I found the idea of swapping the broiler igniter for the bottom one particularly good - I knew exactly what part was broken and how easy/hard the job would be prior to ordering. The part used snap in electric components, so the only work was in removing and re-installing the parts. Working in the oven was by FAR the most difficult part of the entire process.

Removed two nuts and one screw to replace old igniter with new one. Replaced the nuts and screw. Turned on the oven, and it is working fine.

First I went online to find out about the availability of the part. In my search, I found what others had experienced and how they repaired it. Second, I ordered the part and followed others stories on their repair efforts. Third, I unplugged the range and removed the racks. Fourth, I removed the bottom of the oven which lifts out back first. Fifth, I removed the wing nut securing the flame difusser making it easier to access the element. Sixth, I had read that others had problems saving the original screws and/or threaded holes. I sprayed some wd-40 on both screws. They came out and back in without a hitch. Seventh, I removed and replaced the element, snap out, snap in. Eighth, I turned on the oven. It took about 15 seconds to glow but wow, it lit 5 seconds after that. I am my wife's hero!

I removed the back of the range to disconnect the wires to the igniter. Then I removed the two screws holding the igniter, screwed the new one in and reconnected the wires in back.
I was really pleased how easy it was to find the part on the website and how quickly the part came. The whole job was a snap. Thanks!

Furtunately, it was just a replacement of the drip pans. It changed the entite looks of my range for under $ 25.00 dollars. Very satisfied!

Removed what was left of the original clips. Pressed in the new clips and snapped in the themostat blub

Removed the rusted drip pans and replaced them with the new pans. Range looks great and ready for many more years of use!

The igniter was located in the bottom of the stove or broiler section. It was hard to get at, but with a little trial and error I figured out how to take the plate between the oven and broiler. Now the igniter was easily accessable. 2 screws on the igniter bracket, then simply unplug the electrical. The igniter supplied had the identical electrical plug (plug and play). The new igniter works like a charm-oven ignites in about 15 seconds. Piece of cake!!!!!

I read all the reports on your site pertaining to oven igniters and decided to order one. I was amazed when it arrived the next day. I got a lot of tips reading others replys so I lifted off the oven door, took out the racks, removed the 2 screws holding the old igniter and tried to pull it out. There was hardly any slack in the wires, so I pulled the stove away from the wall, took off a breadpan size cover in back and found the wires were zip tied to a tube. I cut the tie and unplugged the wires, but the new plug didn't match so I cut the new plug off and rejoined the wires with butt to butt crimp connecters, which I prefer to wire nuts. I used the insulation and new cover from your kit as my old part had the long ceramic insulator and put it all back together. It works like new again and saved me a lot of money. I am very pleased with your product and service, thanks.

Inserting two stove valve knobs took 10 seconds! No tools necessary.

Same as the other entries in this section.
The only thing I would add is a hint for removing the broiler igniter. As you can see from the oven igniter, the wires connect with a plug. For the top igniter, the broiler, the plug goes through the insulation and then through a hole in the rear panel of the oven. So, when you pull on it, you will think it is stuck or the wire is pulled taut. That is because the plug hangs up on the rear panel.
Stick your finger through the square hole that you can see inside the oven, and follow the wire through the insulation. You will feel the small round hole in the back. You have to wiggle the wire up and around a bit to get the plug to fit through the hole. Then you will have the slack you need to change the plugs.
That way, you don't have to pull the whole oven out and break all the caulking seals.

It took me 10 mins to replace the oven igniter and I did it myself. Oven is working fine now. I saved myself a $300.00 repair bill. Thank you for making the part available and saving me dollars!