Models > 31000PAWD > Instructions

31000PAWD Magic Chef Range - Instructions

All Instructions for the 31000PAWD
16 - 30 of 33
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
My original back leg broke because the floor is uneven. Had to pull it out several times.
Put the back of stove on blocks of wood to get high enough to screw the new leg in.
Parts Used:
Leveler Foot Screw (Nylon)
  • Phyllis from BROWNVILLE, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Wrench (Adjustable)
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The oven bottom was warped and could not be positioned properly in the oven.
Removing the old oven bottom was easy...as it was already outside of its slots. Installing the new one was pretty easy. I placed the oven bottom in the front slots first...then the rear slots...no tools necessary.
Parts Used:
Oven Floor Panel
  • Tara from ALBANY, NY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
My oven door seal had dried rotted
I took pliers to get the old one off, and popped the new one back in its place, and it fit perfect.
Parts Used:
Door Seal
  • Anita from ELKTON, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drip pans were rusted. I had shopped for replacements at local appliance stores without finding them.
Removed the rusted drip pans and replaced them with the new pans. Range looks great and ready for many more years of use!
Parts Used:
Drip Pans - Kit of 4
  • Norma J from Philadelphia, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Thermostat bulb was hanging loose
Removed what was left of the original clips. Pressed in the new clips and snapped in the themostat blub
Parts Used:
Range Thermostat Clip
  • Willi from Old Saybrook, CT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
2 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old and corroded drip pans
Furtunately, it was just a replacement of the drip pans. It changed the entite looks of my range for under $ 25.00 dollars. Very satisfied!
Parts Used:
Drip Pans - Kit of 4
  • Veronica from Miami Beach, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The floor panel of the oven was pocked and in bad shape
I found the panel on the innernet, ordered it and when it arrived I removed the old one and replaced it with the new one.
Parts Used:
Oven Floor Panel
  • Roger from San Juan Capistrano, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
When I decided to do an extra cleaning of the rqnge, I removed the knobs, along with all the other parts and soaked them in the sink....I cleaned the knobs and set them up on the dish drainer to dry for a minute while I cleaned the rest of the stove...I dried the knobs, paced them back on the stove.
It was easy since it just pushes on...
Parts Used:
Surface Burner Knob
  • Betty from Nashua, NH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
thermostat temprature bulb hanger clips
snaped them into oven cavity attached temp bulb job complete
Parts Used:
Range Thermostat Clip
  • Dwayne from Atlanta, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken leveling leg.
This is a no brainer. I am only doing this because you asked. Pull out the stove, tilt it back, remove broken leg, install new leg.
Parts Used:
Leveler Foot Screw (Nylon)
  • Don from Crestwood, MO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
Was this instruction helpful to you?
Thank you for voting!
As easy as it could be
I have worked in maintenance field most of my adult life and all aspects and to change the oven door gasket was no challenge what so ever. It took longer to find my needle nose pliers to remove the old gasket clips and then re-install the new gasket. Maybe 10 minutes total
Parts Used:
Door Seal
  • Phillip from Twentynine Palms, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
Was this instruction helpful to you?
Thank you for voting!
Used stove was missing 1 leg.
My used stove had been dropped by the previous owner. While I could live with the minor scratches on one side the wooden shims holding up one corner were annoying. A new leveling leg was less than $2. I used a pair of needle nose pliers to straighten the mounting hole and screwed the new leg in. This used stove was originally $2000 but I bought it for $999. the new leg plus shipping was about $10. What a deal.
Parts Used:
Leveler Foot Screw (Nylon)
  • Clarence from Monroe, WI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
Was this instruction helpful to you?
Thank you for voting!
leg was bent, also metal receiving bracket bent
Removed stove from slot in wall. Bent rear left leg would not unscrew due to bent metal bracket. Used hacksaw to cut out leg, then straightened metal bracket with small hammer and was able to screw new leg in and adjust height by using level on stove before reinserting stove its slot. Recheck level after pushing back in place and adjust front legs if necessary. If not for bent metal receiving bracket, would have taken much less time. Still easy tho. R'cvd part in two days. Very quick.
Parts Used:
Leveler Foot Screw (Nylon)
  • Virginia from Oceanside, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Wrench (Adjustable)
Was this instruction helpful to you?
Thank you for voting!
Leveling legs were broken during the summer
The range in my classroom had the leveling legs broke off by the summer staff. I ordered two new leveling legs and the night custodian replaced them in about 45 minutes and them leveled the stove. Parts were just as stated and easy to order.
Parts Used:
Leveler Foot Screw (Nylon)
  • Jayne from Willimantic, CT
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers, Wrench set
Was this instruction helpful to you?
Thank you for voting!
Rubber seal was broken
Broke the same day I installed it
Parts Used:
Door Seal
  • Jennifer from Lynn, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 31000PAWD
16 - 30 of 33
Back to Top