2855EGS Jenn-Air Range - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Install New Vent Cover
Installation was straight forward as the new vent cap was sized correctly for exhaust pipe (5 inch). Placed the mounting plate into the exhaust pipe and used 4 SS screws to anchor to house sheathing. The vent flapper was not flat, requiring that I carefully stress relieve it at 250 degrees and hold it flat while cooling to take warp out. Snapped it in place afterwards and then bolted on cover.
Parts Used:
-
Brent from EAST LYME, CT
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
knobs were getting hard to read.
Pulled old knobs off, pressed new ones on. Probably well under a minute for 6 knobs. Anyone with the IQ of a horseradish could have done it. But what was really great was the help and personality of the agent at the other end of the phone. Shipping was as promised, and the entire experience was delightful!
Parts Used:
-
Dave from Bloomingburg, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The original grease filter was damaged in our dishwasher (it is quite fragile) and needed to be replaced.
1. Remove the exhaust vent cover, located in the center of the top of the range. It just lifts off.
2. Swivel the clamp 90 degrees to release the filter.
3. Remove the filter and throw it away
4. Place new filter in place and lock in place by rotating the swivel clamp back 90 degress.
5. Replace the exhaust vent cover
2. Swivel the clamp 90 degrees to release the filter.
3. Remove the filter and throw it away
4. Place new filter in place and lock in place by rotating the swivel clamp back 90 degress.
5. Replace the exhaust vent cover
Parts Used:
-
Martyn from Middletown, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
old nkobs old and discolored
-
WALTER from EL CAJON, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
lost one of the knobs
Ordering and installing was easy. The hardest part was getting the exact match to 20 yr. old appliance knobs. First one I ordered had wrong shaft hole, but it matched perfectly in design. Decided to reorder and just replace all four with matching new-style knobs and the correct shaft hole. Yeah. Looks great and REALLY easy to install.
Parts Used:
-
Sabra from Dallas, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Elec. stove-top knobs (imprinted with HI to LO numbers 1 to 10)worn to non-readable.
Knobs sent fit the shafts, but due to molded internal stop wouldn't seat. Had to drill out the stop, and also file down the shafts a bit for knobs to seat acceptably closer to stove-top.
Parts Used:
-
Lenice from Stuart, FL
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Change the Oil/Grease Filter
It is so easy. Once I found the right size of filter from the website, I ordered it right away. It came in 3 days and I just need to take out the old one and insert the new one. No instruction is necessary. By the way, the price of the filter is one third of that from Jenn-air.
Parts Used:
-
Yong from Houston, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ring adapter was the original and was pretty well worn through.
Removed the old adapter and replaced it with the bright and shiny new one that fit perfectly.
Parts Used:
-
Edward from Brooksville, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old Stove Top
-
Robert A from Farmington `, CT
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Thermostat bulb was hanging loose
Removed what was left of the original clips. Pressed in the new clips and snapped in the themostat blub
Parts Used:
-
Willi from Old Saybrook, CT
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
2 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Existing knobs were bent & unreadable
-
James from Smithfield, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
1 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Over the years the numbers has worn off the knobs.
Fed-Ex delivered the package and within 10 min I had open the package, removed the old knobs and installed the new ones, My wife was very impressed with the ease of the transactionl. It is good to know that we can still get parts for our cook top even though it is 26 years old. Thanks for every thing.
Parts Used:
-
John from Flippin, AR
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
1 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Renters removed leveling legs from refrigerator. I don't know why!
-
Don from Frankfort, KY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
1 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
oven light burnt out
1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes
Parts Used:
-
William from Schwenksville, PA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
3 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
burned oven bulb
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.
Parts Used:
-
Ivanka from Atlantra, GA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
3 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!