283440A Frigidaire Range - Instructions

1- put in new thermostat 2- put in new gas valve 3- put in oven igniter ....3rd time a charm. Now I have all new oven parts! My husband installed and said it was pretty easy, have to take the oven door off and inside bottom out.

Oven would not light upon setting for oven heat-up. Igniter would glow, but no gas flow. Gas Valve safety not sensing enough current draw from igniter to open gas valve. Original igniter measured 175 Ohms on Volt-Ohmmeter. New Igniter measured 74 Ohms before installation and use. Installed and spliced into existing wires using good quality wire nuts and tucked wiring into wire areas ensuring it was away from burner flue. Oven lit on first start-up! Problem fixed! Easiest to get to by removing broiler drawer, pressing catch tangs in from outside rails using a small screwdriver. 1 screw of 2 on igniter mount was stripped and difficult to remove, but working with pliers and nut driver was able to remove it with some difficulty. New Igniter hangs fine with 1 screw. .

I bought and paid for 4 drip pans for my Tappan stove. I received 4 metal ones. With your authorization I returned them,
paying $18.00 postage. Since it was your mistake a believe you should reimburse me for that expense.

Mary Lee
(703)578-1942

Remove oven racks and bottom oven panel cover.Removed old igniter.one screw was stripped so that slowed me down quite a bit! Used a small vise grip tool to remove screw! installed new ignighter,cut existing wires; spliced in new wires( be sure to unplug appliance) tested ok. Reassembled.

Replaced the ingintion module, still did not work, replaced the burner complete with new ingiter , it now works but another one quit . the front right one has 5 ohms resistance ,replaced with new one with 0 ohms, the back left has 2 ohms resistance and now it does not work , will need to replace that burner allso. too bad you can't buy just the spark module for the burner.

Really easy to do, did not have to bring stove out from the wall! Turn power off to the stove. Remove the lower drawer. Remove the oven rakes. With a slotted screwdriver remove two screws in back of bottom oven cover, use 1/4 inch socket to remove two screws in front. Remove bottom oven cover. You can then see the part to be removed which has two wires going into it, the unit looks identical to the new part which heats up and lights the gas grill for the oven. I cut the two wires from the old part, remember which is the upper and lower; remove two screws holding onto part. Wire new part remembering top and bottom. Push extra wire down into bottom drawer and then mount new part with two screws. Turn power back on and try oven. Lite right away for me so I knew I had replaced the bad part. Reassemble and Enjoy!!

Your website is great...easy and it literally took me no mote than 5 minutes to find what I needed and order...and received it VERY quickly. Must say I was dreading going to some parts house that we have in our town in bad area, and searching on dusty shelves for what I needed...am so glad I found you!!

first I removed oven draw for access, then removed the two screws with a nut driver, next removed the two wire nuts and the old element was free. Replaced new element in reverse steps of removing old and the new part ignited the stove within 30 seconds, but now I have no excuse for not fixing dinner!! Thanks for promt shipping, it arrived early than anticipated.

It was so easy. I am 66 yrs old. It only took 30 minutes and a screwdiver. I was totally amazed and I thank you.

pulled drawer out and took old igniter off and replaced it

take off the old by unsceawing it scraw thenew one onput the wires down the back throw the hole put the wires to gather and cap tham plug the elect. back in and turn it on for to test it wow it worked he he ...richard

Removed oven door, removed oven floor. Unscrewed skirt with attached igniter and gas tube. Two nut screws hold igniter to burner. Remove old igniter and replace with new, reattach two wires with supplied wire nuts. Replace oven floor and door. Oven lit right up, pizza anyone?

Thank you, Thank you and thank you!!! I couldn't be happier and I save over $200 in repair. My repair was very easy after watching the video. I cut off the wire and ensure that the new one are attached into place. Placed all parts back and boom, the oven starts working a new.

Opened the oven, removed the bottom plate located the ignitor within arms reach, removed two screws and a snap out part. replaced with the new ignitor and put the stove bottom on and waala...DONE
I have ordered all my parts from Parts Select and have never had a problem. Thank you. Jody in Montana

I unplugged the stove then pulled the disconnected the wires that controled the igniter. I took the two screws off that held the igniter to the pilot port. I hand to cut the wires on the new igniter to some-what match the lenght of the broken igniter. Then I cut the connectors from the old part and used the fire resistant wire nutes that where included with the new igniter and connected it all. Put all the screws in tight, double checked every thing. Finally I plugged it in and it was working.