2537041341F Kenmore Refrigerator - Instructions

Installed new valve.There are several pieces of tubing coming off of the valve. Pay close attention to where they go. Color coordination is poor on the new valve.

Removed old water pump and cut off ends of all lines. Plugged them into each water inlet/outlet and turned it on. Instant water to dispenser but took about 6 hours for ice maker to get water. Had to prime the ice maker. Works great and saved a lot of money ordering parts from you. Thanks.

1. Turn off water in line to refrigerator. 2. disconnect hose from refrigerator. 3. Remove back cardboard panel at bottom of refrigerator. 4 Remove 2 screws holding in the valve assembly at bottom right. 5. best way I found to remove hoses (all color coded) is to cut with razor knife at the white collar. cut clean and square. 6. disconnect electrical (also color coded) 7. connect hoses to valve assembly by pushing hose firmly into hole. If you are familiar with PEX then this is the same. Reconnect electrical. Reconnect to refrigerator... 3,2,1 your done. It will take a couple cycles to get the air out of the lines.

Followed the instructions from another person in the Part Select water valve section and from the video on the same page. Excellent instructions and very easy installation. Water dispenser and ice maker began performing properly as soon as the refrigerator was plugged back in to the power.

Had a leak every night from refrigerator couldn't understand where from. Went on line and found some articles. I was referred to this sight by ads the articles and then in how to. I was pleased that a customer wrote their own instructions on what to do it was more concise clear and made preparation easier. First label towel cup and bucket needed too. Turn off water supply and electrical cord unplug then remove cover behind refrigerator vacuum and clean then. Water makes a mess so clean dry first. Then mark your hoses to remember order. Next remove old inlet and put in bucket it's pressure clamps so push in and it locks I chose to suction pipes and check for damage to pipes pin holes etc next I inserted into new inlet in order. At that time I turned water valve on checked for leaks at initial insert and new inlet. Next I plugged in unit cord. Waited. No leaks so far left for 30 minutes ran ice machine and water dispenser waited 20 minutes no leaks yet. Unplugged refrigerator unit. Installed the inlet completely to base and closed back paper panel after wiping water. Waited 24 hours then smiled no leak. Job done so far 2 weeks all clear. Hope this helps you will need screws driver and wrench for copper or main line I did find same part for less but this sight help me with good instructions the one they provide is for engineers architects lol not me I'm DYI

This was the first time I ever installed a water inlet valve in a refrigerator. I viewed the Parts Select youtube repair video that is available online. In fact, I viewed it a couple times. Ultimately, the actual installation of the water inlet valve went exactly as shown in the youtube video. I did not experience any problems with the installation and was quite happy with the experience.

i was trying to figure it out but eventually it fix it self even when i get the part the problem seems to be fix on its own i unpplug the eletrical cord from the wall for over three hours and plugged back in and after 2 more hours it works so i am confussed dont know what happen i did not change any part so i have one brand new inlet water

Pulled out the fridge from the wall, unplugged it, and turned off the water supply. Took off the cardboard backing at the bottom of the fridge. Cleaned the dust and gunk. Unscrewed the old valve. Unplugged the 3 electrical connections. Since the new fittings for the water lines were different, we unscrewed the old ones, lopped off the nipples, and inserted the ends of the water lines into the new connections (they were super easy - just push the line in until it clicks). Reattached the valve. Reattached the cardboard. Turned water back on, and plugged in the fridge. Our ice maker still didn't make cubes, though. So I took out the fill valve from the top rear of the fridge. It had a tiny piece of ice lodged in the bend of the back, right above where it connected to the water line. I rinsed it out, reinstalled, and now we have a full bucket of ice!!

The changing of the water valve was pretty straight forward. First shut the water off to the ice maker, then pull the refrigerator out. Once that is done, then I removed the cardboard covering with a cordless drill, loosened the screws that held the water valve in place. The water valve assembly is colored coordinated so disconnecting and reconnecting the lines to the new valve assembly was pretty easy. Reattached the cardboard covering pushed refrigerator back and place turn on supply line and waited for the ice maker to fill up. After several cycles on the ice maker I made one slight adjustment on the ice cube size behind the cover of the ice maker. Total time one hour, then waiting for the ice maker to cycle a few times to ensure all was working properly.

watched the youtube video from PartsSelect and was able to remove old water inlet valve easily and install new one with little effort. The hoses on my refrigerator were a bit different than shown in video, but I was able to modify them and it's working just fine now. Thank you PartsSelect !

This was probably the easiest repair I have done on this refrigerator. I pulled the unit away from the wall, turned off the water, and disconnected the hose. I have a wooden floor in my kitchen so I was careful to put a towel under the hose and valve. Very little water drained out but I kept the towel there for insurance. After removing the access panel, I removed the two screws holding the valve in place, slid it back to where I could unplug the wiring connected to it. The connectors are color coded so there is no worry about putting them back incorrectly. The new valve uses push-in type water connections, so you have to cut the old style connections off of the plastic water lines. Kitchen shears did this easily. Then is was just a matter of pushing each line into the proper connector on the valve, reattach the electrical connectors, and slide the valve back in place. Reinstall the screws, reinstall the access panel, hook up the water hose, slide the unit back into it's niche, and run about a gallon of water through the dispenser and you are done.

Purchased a replacement part only to find the new part had push on fitting and my part has screw on fittings. Went to Youtube where Partselect had a video on how to replace the part from screw fittings to push on fittings

I turned off the water, removed the cardboard cover from the back of the refrigerator; removed the 2 screws holding the water valve in place; unscrewed the plastic tubing from the valve; unplugged the wires to each solenoid (3); the old valve had threaded connections for the plastic water lines, the new valve didn't; I had to cut the ferrel off of the plastic lines so I could insert them into the new valve and then press the connector into the valve (I didn't anticipate something like this, but it worked fine); I reconnected the wiring and screwed the valve back into place. The ice maker started making ice and the water stopped dripping from the dispenser. The best $65 I've ever spent.

The water flow on or refrigerator was just trickling out. After trying to make sure there was no kink in hose, I called for replacement. Water flows great now... actually better than when new.

Turned off the water supply ,pulled the plug removed two screws to access theater lines the new valve body was a little different than the original I had to cut off the end of each hose and push them in to the new connections the hoses are size and color coded replaced the two screws put the water line on plugged it in and turned on the water checked for leaks twice and replaced the back cover