All Installation Instructions for Kenmore Refrigerator 2537034241G

My fridge temp was warm. Freezer temp was ok, but fluctuated some.

I checked the dampener, it worked. The compressor and fan worked. I knew because my freezer was still hovering around 10 degrees. Coils were clean. Thermistor was the only thing it could be. Took all my shelves out. Removed four screws. Took the back panel off. The thermistor sits tucked in on the side. I piped it out, in clipped it. Used my multimeter to test the numbers. Numbers were off just a bit. Ordered the part. Crossed my fingers.,took less then 5 minutes to put the part in. Plugged in the fridge. It was sitting at 33 degrees in about an hour and a half. I can’t believe I fixed it. I knew NOTHING about refrigerators. For how big my fridge is, it would have cost 3,000 and up to get a new one with the same cu ft size. Instead, it cost me $44. That includes shipping. Thank you Parts Select!! Made it so easy to pick the correct part for my model fridge!

Parts Used:

SENSOR,TEMPERATURE,10K,NTC

Cindy from AMARILLO, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

49 of 78 people found this instruction helpful.

Was this instruction helpful to you?

Roller screw recipients broke out. Can't be repaired.

Was not able to repair. Wasn't rollers I needed. Plastic screw recipients in front on frame had broken out so rollers weren't the problem. Tried gluing back pieces to no avail. Crisper frames are poorly designed.

Parts Used:

Refrigerator Roller

hellen from SPRINGFIELD, MO
Difficulty Level:
Very Difficult
Total Repair Time:
More than 2 hours
Tools:
Screw drivers

18 of 22 people found this instruction helpful.

Was this instruction helpful to you?

you r label (this end in arrow is wrong

placed filter in sideways

Parts Used:

Air Filter

melvin from BASKING RIDGE, NJ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

15 of 25 people found this instruction helpful.

Was this instruction helpful to you?

Not making ice in both ice maker or dispensing water

To confirm my diagnosis I first replace the filter still no water flow.
Check water supply from the wall valve: ok
Remove the entire inlet valve assembly and sit it over a small bucket.
Disconnect the tubing from the bottom of the 1st selenide valve: this is the one leading to the filter.
Place cup under water dispenser and activate dispenser. No water discharge from inlet valve confirm valve is bad.
Install the new valve matching the colored tubing with the color on each inlet valve.
Re-connect the water supply place container under water dispenser and activate: There will be a large gush of air then water. Dispense aprox 1 gallon of water to confirm all the air is purged from the system. Your refrigerator is now back to dispensing water and making ice.
Good luck everyone - Neville

Parts Used:

Water Inlet Valve - 4 Coil

Neville from LITHONIA, GA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Wrench (Adjustable)

10 of 12 people found this instruction helpful.

Was this instruction helpful to you?

The left side roller broke away from the crisper cover frame

I removed and separated the crisper tray and cover from the refrigerator.
Removed the left side rail from the damaged cover and discarded the old cover.
I added the new roller to the new cover and replaced the side rail to the new cover and reassembled into the refrigerator

Parts Used:

Refrigerator Crisper Drawer Cover Support - Left Side

Refrigerator Roller

Robert from CRANSTON, RI
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

9 of 10 people found this instruction helpful.

Was this instruction helpful to you?

2 drawer undercounter beverage ref not getting cold enough. Wont get below 48°

Took drawers out by removing 2 screws on top of rail near front, then popped black plastic cover off in lower right inside cabinet...sensor just un plugged and new one plugged in easily...did not fix problem though...display set at 34 but bottom drawer reads about 40 at best and upper drawer reads around 55...dont think the 3 little fans inside on back wall have been running

Parts Used:

SENSOR,TEMPERATURE,10K,NTC

Tim from SYLVANIA, OH
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

8 of 11 people found this instruction helpful.

Was this instruction helpful to you?

No water to the ice maker or water tap.

Removed valve unplugged valve from electric removed water lines from valve and then reverse procedures then turn on water and use.That was it.

Parts Used:

Water Inlet Valve - 4 Coil

Laura from LANCASTER, CA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

4 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Water filter would not disconnect from OEM Water Filter Base

Disconnect the two water supply tubes at the base of the Water Filter Base. Using a 7/16" open end wrench, press up on the blue "O" rings to disconnect the tubes. Use a Using an 8" long magnetic phillips head screw driver I was able to unscrew the 4 short screws holding the original water filter base and the immovable attached water filter. Replacement was easy. Simply slide the new base into the fixed slot on the refrigerator and reinstall the 4 holding screws. Reconnect the water supply tubes to the Water Filter Base. Install a new water filter.

Parts Used:

MANIFOLD FILTER

Richard from SEATTLE, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

NO PROBLEM JUST DECIDED IT WAS TIME TO CHANGE FILTER

VERY EASY SLIDE OLD ONE OUT AND PUT NEW ONE IT

Parts Used:

Air Filter

Gregory from POTTSTOWN, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Wrong Part sent!!!!!

I did not do a repair. You sent the wrong part & I didn't open the package but I can't get hold of anyone to return the part and get the correct part.

I am very upset that no one will help me. I paid $ 37.28 for the part I ordered and then the wrong part was sent

The sku # on the package is 242010901.This is a roller type part and I ordered a small wheel.
I can't even find a return address to send it to.. Please help me
Elizabeth Romage
libbieinrichmond@comcast.net
8042627963

Parts Used:

ROLLER Assembly

ELIZABETH from HENRICO, VA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

condenser fan is no longer holding running speed

Removed the baskets/containers from freezer compartment. Removed back panel from the freezer interior.
Swapped the fan on the mount
Tested and reassembled fully
Back in working order

Full steps followed
https://www.youtube.com/watch?v=73rubWwQork

Parts Used:

MOTOR

Joshua from AKRON, OH
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

New off brand water filter could not be removed from the water filter base

Removed the water lines from the old base. Installed new base and reconnected water lines. Installed new filter.Turned on the water line behind the refrigerator. Opened Refrigerator door to watch for leaks. No Leakes. The new filter base was

Parts Used:

MANIFOLD FILTER

James from ELK GROVE, CA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Water outlet tubing leaking in elbow behind water filter

Most difficult and time-consuming part of the job was clearing the refrigerator of food and shelving. Replaced tubing as it had split in the factory bend of the tubing directly behind the water filter. Take your time and don't get in a hurry.

Parts Used: