25348027893 Kenmore Refrigerator - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
freezer worked frig was warm. Ice maker is still not working
Removed two screws to get to defrost time pull panel down remove two screws holding time and reinstall
Parts Used:
-
steve from Kirkland, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
loud noise fan blade broke,off balance
take 1/4 hex screws out clean out dust ,remove old fan blade replace with new install bolts .
Parts Used:
-
EDWIN from ELWOOD, IN
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken drawer
Bought a new drawer and just used the clear front from the broken drawer. Very easy to replace. Also fast delivery , thank you part select.
Parts Used:
-
Antonia from Germantown, MD
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
2 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken shelf
-
Rafael from Puerto Rico, AL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken Glide
-
James from Staten Island, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
sheft ends brolen
Cleaned and removed old ends, applied new ends and installed. Ends fit to order, shipping quick and parts affordable. Thank you
Parts Used:
-
Helen from Gulf Breeze, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
door end cap broken,
Put the new ordered door end caps in place, everything worked fine.
Parts Used:
-
Edward from Piscataway, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Wrong size listed on website.
The end cap is easy to remove and replace. The personnel at PartSelect was extremely helpful in re-ordering the correct part.
Parts Used:
-
Elizabeth from Weems, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
frezzer iceing over and not cooling the refrigerator
Just removed the two screws and unpluged it.
Then I pluged the new one in and replaced the screws. It runs like a brand new reffrigerator.
Thanks for the fast delevery. Will do busness with you in the future.
Then I pluged the new one in and replaced the screws. It runs like a brand new reffrigerator.
Thanks for the fast delevery. Will do busness with you in the future.
Parts Used:
-
Marcus from Pine Hill, AL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
1 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
clips on both end caps we broken and the crossbar kept falling off.
First i pulled the crossbar off the door, then I pulled both end caps off the crossbar and then I
put the two new end cap on the crossbar and then tapped snoggly into place with the palm of my hand. Job done. took all of about 5 seconds.
put the two new end cap on the crossbar and then tapped snoggly into place with the palm of my hand. Job done. took all of about 5 seconds.
Parts Used:
-
Frank from Orange Park, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
End caps broken
End caps snapped out of door,
Replaced with new caps
Replaced with new caps
Parts Used:
-
Russell from Clevelamd, TN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
coil Iceing up
took 4 screws out of the discharge vent on top of the refrigerator section and unpluged the wiring harness and put the section on the counter and unscrewed the timer and put the new one in and reinstalled the assembly and plugged the Jack and put the 4 screws back in, and rotated the timer and put it on defrost removed the back and check the heaters and drain .
Parts Used:
-
Thomas from Stuart, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Freezer built ice, fridge not cold enough and running constantly.
Removed front low grill, removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the wires. Reversed process to install new timer.
Parts Used:
-
LUIS from CENTENNIAL, CO
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
1 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The door end caps were broken and not fixable
I simply placed the retention bar between the new end caps and popped it into place. Took about 10 seconds to complete.
Parts Used:
-
Ryan from Coralville, IA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Left bottom part of door rusting out
took door off. sanded rusting hinge and greased. installed door hinge washer. I had to install a larger washer over hinge bearing to help support the door where it was rusting. no sweat. works like its new. thanks to you guys for having the parts.
Parts Used:
-
William from Moulton, TX
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Socket set
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!