All Installation Instructions for Kenmore Refrigerator 25348027893

Freezer door caps

They were the wrong parts. I read a question another person asked and it advised to order these parts. Didn't want to waste my time anymore and threw them away.

Parts Used:

Door Shelf End Cap - Left or Right Side

Lisa from LAS VEGAS, NV
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Door brackets were broken and missing

Assembled brackets and pressed into place on refrigerator door

Parts Used:

Door Rack with Endcaps

Arthur from OAK GROVE, KY
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The hole on the handle mounting block was too low

I had to loosen the screw holding the mounting block and increase the hole size to fit the screw on refrigerator

Parts Used:

Handle Mounting Block

Sadrudin from SAN DIEGO, CA
Difficulty Level:
Difficult
Total Repair Time:
30 - 60 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Light wouldn't turn on when door opened

Unplugged fridge, opened the door, used flat head screwdriver to pop off old switch, unplugged wires, plugged in new switch, popped it back in, and plugged the fridge back in. 2 minute fix.

Parts Used:

Light Switch

Matthew from SOUTH BEND, IN
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

edges of drawers had broken off, The drawers were just sitting on the shelves.

raised the sides of the drawer front up, then pulled the front straight up. Then put the front in the slots of the new drawer and pushed down. I gave it a light tap on the top corner and it locked into place. I put my food stuffs back in the drawers and slid them back into the refrigerator. Job done in about eight min, for two drawers.

Parts Used:

Upper Crisper Drawer

Lower Crisper Drawer - Front NOT Included

nancy from LA FAYETTE, GA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Broken pan cover.

Installed salvaged pan cover edge guards from broken pan cover. I installed new pan cover in grid.

Parts Used:

Crisper Shelf Glass Insert

John from MULLINS, SC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Door handle had too much space between the door and handles.

Use the rubber brushing to fill the gap.

Parts Used:

SCREW

Handle Mounting Button

Michael from MEMPHIS, TN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

End caps were broken, shelf bar kept falling off.

I unsnapped the old clips from the bar, installed one end cap to freezer door, clipped other end cap to bar, slid bar into end cap installed in door then snapped other end cap into place. Repeated for second shelf bar as those end caps were broken as well. No tools were needed.

Parts Used:

Door Shelf End Cap - Left or Right Side

Joseph from INDEPENDENCE, MO
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

light bilb went out

replaced it

Parts Used:

Light Bulb

Denise from Landover, MD
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

No freezing or cold in either freezer or refridgerator - compressor did not run.

Traced issue to defrost timer ( burned compressor & element contacts). This unit is mounted next to the temperature adjustment control in the refridgerator area - right in front. Removal of plastic cover provided easy access to the timer. Unit unscrews from the mounting then unplugs. Installation is reverse of removal.

Parts Used:

Defrost Timer - 60Hz 120V

George from Sunnyvale, CA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Defroster didn't work

Ordered a new defroster timer and replace old one. It works just fine. A $35 repair vs a $500 new appliance.
Cool.
GWE

Parts Used:

Defrost Timer - 60Hz 120V

George from Eatonville, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Refer iced up and would not keep the bottom cool. It was 70 Farenheit inside.

I simply removed 4 screws holding the casing and then 2 more holding the timer. It was very easy. I then replaced the timer by unplugging and plugged the new one in. I replaced all the screws and the job was done. Less than 30 minutes. I was very impressed with the shipping time. When I ordered the part, I had it the next day.

Parts Used:

Defrost Timer - 60Hz 120V

Larry from Newton, KS
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set

2 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

door shelf end caps were broken

removed broken end caps, took a small screwdriver and simply applied a little pressure to release them. Pushed new end caps into place (they just snap in). Presto done!!

Parts Used:

Door Shelf End Cap - Left or Right Side